Abstract:Demolished concrete, as one main form of construction and demolition wastes, has been widely studied of being utilized as recycled aggregates (RAs) in new concrete production. However, existing studies of applying RAs have been limited to the mechanical and durability issues of cementitious composites containing RAs. There has not been sufficient research of adopting RAs in cementitious products to also address the environmental sustainability. On the other hand, existing research utilizing cementitious products (e.g., concrete pavement) for air purification purpose have not adequately considered RA usage. Aiming to address the two sustainable objectives (i.e., waste diversion and air purification) simultaneously in concrete mix, this research adopted a two-step approach. Firstly, we studied and identified the optimal mix design of pervious concrete containing TiO2-soaked recycled coarse aggregates (RCAs) in order to achieve the higher compressive strength; secondly, we investigated the photocatalytic performance of pervious concrete containing RCAs coated with TiO2 photocatalysts. The photocatalytic performance of pervious concrete was also tested by applying a 10-min heavy rainwater wash. Experimental test results revealed that the internal voids of adhered mortar enabled RCAs to absorb more TiO2 particles. The NO degradation rate of TiO2-soaked RCAs increased from 71.4% to 80.6% when RCAs' size decreased from 15-20 mm to 5-10 mm. The orthogonal experimental investigation indicated that water-to-binder ratio had the most significant effect on concrete compressive strength, followed by ratio of RCAs to binder, and replacement ratio of RCAs to natural aggregates. The optimized mix design for pervious concrete containing RCAs was identified to achieve highest strength (i.e., water-to-binder ratio at 0.35, coarse aggregate-to-binder ratio of 3 by mass, fly ash replacement rate to Portland cement at 5%, and 50% replacement ratio of RCAs to NCAs). The concentration of TiO2 solution at 0.3% was identified as the optimal ratio to achieve the highest NO degradation rate at 70% before rainwater wash. The NO degradation rates of pervious concrete still reached nearly 50% after 10-min heavy rainwater wash, indicating that pervious concrete using RCAs coated with TiO2 could largely maintain its photocatalytic capacity. This study addresses two main social and environmental issues in developing countries (e.g., China), namely overwhelming amount of construction & demolition wastes being generated, and air pollution. It leads to the cleaner production in concrete pavement construction by achieving the optimization between waste reuse, air purification, and engineering properties of porous concrete. (c) 2019 Elsevier Ltd. All rights reserved.

Study of the physical and mechanical properties of permeable concrete with the addition of TiO 2 for the treatment of sewage

Developing Novel Photocatalytic Cementitious Permeable Pavements for Depollution of Contaminants and Impurities in Urban Cities

Toxicological Effects of Leachates Extracted from Photocatalytic Concrete Blocks with Nano-TiO2 on Daphnia magna

Enhanced Fe-TiO2 Solar Photocatalysts on Porous Platforms for Water Purification

Studying properties of pervious concrete containing recycled aggregate loaded with TiO<sub>2</sub>/LDHs and its liquid pollutant purification

Evaluation of Nitrogen Oxide Reduction Performance in Permeable Concrete Surfaces Treated with a TiO2 Photocatalyst

Studying properties of pervious concrete containing recycled aggregate loaded with TiO2/LDHs and its liquid pollutant purification

Photocatalytic properties, mechanical strength and durability of TiO2/cement composites prepared by a spraying method for removal of organic pollutants

Influence of the Addition of TiO2 Nanoparticles on the Self-Cleaning Capacity of Cementitious Composites

Reducing the effects of clogging and surface wear on the radiative properties of concrete blocks produced with recycled glass by incorporating titanium dioxide nanoparticles

Effects of the use of TiO2 on the early ages of white cement-based mortars: analysis of chemical, physical, mechanical, and photocatalytic properties

Wastewater treatment containing organic solvent from the production of hybrid membranes

Studying the Mix Design and Investigating the Photocatalytic Performance of Pervious Concrete Containing TiO2-Soaked Recycled Aggregates

Eco-friendly concrete: Combining treated wastewater and recycled aggregates

The Influence of TiO2 Nanoparticles on the Physico–Mechanical and Structural Characteristics of Cementitious Materials

Mechanical and hydraulic performance of pervious concrete pavements: experimental evaluation

Assessment of treatability of the Tietê River through a process of coagulation-flocculation associated with hydrodynamic cavitation and ozonation

Corrosion Performance of Nano-TiO2-Modified Concrete under a Dry–Wet Sulfate Environment

Effect of Engelhard titanosilicate microporous material on photocatalytic performance of cement

Study on Photo-catalytic Efficiency and Durability of Nano-TiO2 in Permeable Concrete Pavement Structure

Effect of TiO2 Nanoparticles on the Fresh Performance of 3D-Printed Cementitious Materials