Abstract:The C=C double bonds in the main chain of hydroxyl-terminated polybutadiene (DHTPB), obtained by the degradation of polybutadiene rubber, were partially epoxided using m-chloroperoxybenzoic acid (mCPBA) as epoxidation reagent. A series of epoxided HTPBs (EHTPB) with different epoxy contents (5%, 10% and 15%) were prepared by tuning the molar ratio of mCPBA to C=C double bonds. The structures of EHTPBs were characterized by Fourier transform-infrared (FTIR), nuclear magnetic resonance (H-1-NMR) spectroscopy and gel permeation chromatography (GPC). The epoxy percent in EHTPBs from H-1-NMR spectra was in accordance with the design. In addition, a series of EHTPB-based polyurethane elastomers (EPU) were prepared by the reaction between EHTPB and 4,4'-diphenylmethane diisocyanate with 1,4-butanediol as a chain extender. Mechanical and thermal properties of the EPU samples were characterized by tensile test, differential scanning calorimetry (DSC) and thermal gravity analysis (TGA). With increased epoxy percent in EHTPB, the Young's modulus and the tensile strength of the EPU samples increased, whereas the elongation at break decreased. The sample EPU10 prepared with 10% of epoxy had the best mechanical properties with 8.82 MPa as Young's modulus, 7.83 MPa as tensile strength, and (485 +/- 23)% as elongation at break. The elasticity recovery of the EPU sample was slightly better than HTPB-based PU (EPU0). The results with TGA test showed that the thermal degradation of EPU, similar to EPU0, was divided into three stages. However, the EPU samples had better thermal stability with the initial degradation temperature at 210 degrees C, about 30 degrees C higher than that of EPU0. The DSC results showed that the glass transition temperature (T-g) of EPU gradually increased as epoxy percent was increased, though still lower than that of HTPB (FHTPB) based PUs prepared by free-radical polymerization.

Synthesis and properties of reactive polyurethane hot melt adhesive based on a novel phosphorus-nitrogen-containing polyol

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Synthesis and properties of flame-retardant reactive hot melt polyurethane adhesive

Polyhydroxyurethanes (PHUs) Derived from Diphenolic Acid and Carbon Dioxide and Their Application in Solvent- and Water-Borne PHU Coatings

Study on Preparation and Performance of Reactive Polyurethane Hot Melt Adhesives Based on a Polycarbonate Diol and a Polyester Diol

Reactive polyurethane hot melt adhesives based on polycarbonate and sebacic acid-based polyester polyols

Facile Synthesis of a Novel Hyperbranched Poly(urethane-Phosphine Oxide) As an Effective Modifier for Epoxy Resin

Facile synthesis of polyester-polyether block copolyols for the sustainable high-performance polyurethane reactive hot melt adhesives

Reactive hot melt polyurethane adhesives modified with pentaerythritol diacrylate: synthesis and properties

Synthesis and properties of poly(bisphenol A acryloxyethyl phosphate) as a UV curable flame retardant oligomer

A New Phosphorus Flame‐retard Curing Agent for Epoxy Resin/anhydride System

Synthesis and thermal degradation behaviors of hyperbranched polyphosphate

Synthesis and properties of a novel hyperbranched polyphosphate acrylate applied to UV curable flame retardant coatings

Synthesis and thermal decomposition of a novel hyperbranched polyphosphate ester used for flame retardant systems

Synthesis, characterization and properties of biomass and carbon dioxide derived polyurethane reactive hot-melt adhesives

Synthesis and characterization of flame‐retardant polyurethane based on new chain extenders

Synthesis and properties of a novel phosphorous-containing flame-retardant hardener for epoxy resin

Photopolymerization behaviors of hyperbranched polyphosphonate acrylate and properties of the UV cured film

Combustion and Thermal Behavior of Polyurethane Acrylate Modified with a Phosphorus Monomer

CO2-based Poly (propylene Carbonate) with Various Carbonate Linkage Content for Reactive Hot-Melt Polyurethane Adhesives

Synthesis and properties of hyperbranched polyurethane acrylate used for UV curing coatings