Abstract:The promising performance from the platinum group metal (PGM) catalysts make them the most practical catalysts for the commercialization of the polymer membrane fuel cells (PEMFCs). However, the excellent initial performance is not good enough for massive applications, particular for the fuel cell vehicles, which requires the long-term durability. Both the performance and the durability of catalysts strongly impact the applications in a wide range of operations of fuel cells, from stationary power generation to the transportation power propulsion. Catalyst stability plays a very important role on reducing the operation cost and increasing the lifetime of PEMFCs. Herein, a concept is proposed, which enhances the lifetime of PEMFCs through engineering the surface of catalyst supports. By covalently grafting NH2 groups on carbon (NGCB) surface, followed by polymerizing polyaniline (PANI) onsite on NFCB surface (using introduced NH2 groups as precursor), Pt L-edge goes to higher energy level, suggested by XAS measurement. Such modification can increase the barrier for Pt’s oxidation. In this study, carbon supports with different PANI loadings were synthesized and the Pt nanoparticles were loaded onto these supports. The synthesized catalysts were characterized for their morphology and structure using TEM, XRD, BET and Hg porosimetry. Both RDE and MEA tests were carried out for these catalysts for their fuel cell performance. The results show that the energy levels of Pt L-edge were increased with PANI loading. Besides, the membrane electrode assembly (MEA) testing results prove that the catalyst stability was improved with PANI loading in certain range. Three different PANI loadings were analyzed: 0.2, 0.25 and 0.33 in mass fraction of NFCB. MEAs results show that the beginning of life (BOL) performances of three catalysts were almost same. But when it comes to the catalyst stability test, the performance losses between BOL and EOL at 0.8 A·cm-2 in air are 120 mV, 90 mV and 45 mV for the three catalysts, respectively, after 30k square wave cycling using the standard testing protocol from the Department of Energy (DOE).

Development of effective bimetallic catalyst for high‐temperature PEM fuel cell to improve CO tolerance

Nanostructured Ultrathin Catalyst Layer Based on Open-Walled Ptco Bimetallic Nanotube Arrays for Proton Exchange Membrane Fuel Cells

The influences of catalyst combination on the high temperature proton exchange membrane fuel cell

Pt Nanoparticles on Atomic-Metal-Rich Carbon for Heavy-Duty Fuel Cell Catalysts: Durability Enhancement and Degradation Behavior in Membrane Electrode Assemblies

Catalyst Development for High‐Temperature Polymer Electrolyte Membrane Fuel Cell (HT‐PEMFC) Applications

Fluorination-enabled Interface of PtNi Electrocatalysts for High-Performance High-Temperature Proton Exchange Membrane Fuel Cells

Pt3Co/C Catalyst on the Nitrogen-Doped Carbon Support with High Catalytic Activity and Stability

Improving Pt Utilization and Electrochemical Activity of Proton Exchange Membrane Fuel Cells Through Surface Modification of Carbon Nanotube Catalyst Support

Atomic metal, N, S co-doped 3D porous nano-carbons: Highly efficient catalysts for HT-PEMFC

Strong Coupling Effects between Single Metal Site-Rich Carbon and PtCo Intermetallic Catalysts for Heavy-Duty Meas

Catalytic Approaches Towards Highly Durable Proton Exchange Membrane Fuel Cells with Minimized Pt Use

Performance improvement of ultra-low Pt proton exchange membrane fuel cell by catalyst layer structure optimization

Atomically Dispersed Single Metal Sites for Promoting Pt and Pt3Co Catalysts in Heavy-Duty Meas

Performance degradation of 1 kW proton exchange membrane fuel cell stack using graphitized carbon supported Pt nanoparticle catalyst

Graphene-nanopocket-encaged PtCo nanocatalysts for highly durable fuel cell operation under demanding ultralow-Pt-loading conditions

Synthesis and characterization of carbon riveted Pt/MWCNTs@TiO 2-TiC catalyst with high durability for PEMFCs application

A P–O functional group anchoring Pt–Co electrocatalyst for high-durability PEMFCs

Durable Electrocatalyst Support Materials Based on N-Doped Mesoporous Carbon Nanofibers with Titanium Nitride Overlay Coating for High-Performance Proton Exchange Membrane Fuel Cells

Enhanced Catalyst Stability Via Chemically Grafted Polyaniline Groups for PEMFC

Preparation and Performance Study of an Unsupported Pt Catalyst for Proton Exchange Membrane Fuel Cell

Synergy of Pt-Free Single Metal Sites for Promoting Pt and Pt<sub>3</sub>co Ordered Intermetallic Catalysts for Fuel Cells: Performance and Durability Improvements