Abstract:This study investigated the machinability of AISI H13 hot work tool steel with a hardness of 54 HRC, which has been deep cryogenically treated using the electro-erosion machining technique, one of the unconventional manufacturing methods. The machinability parameters used in the study were determined as current (4, 8 and 12 A), pulse time (200, 300 and 400 μs) and three different electrodes (Copper, Graphite and Tuncop). The experimental design was designed according to the Taguchi L 27 model, and machinability tests were carried out to examine the results obtained from the experimental study both experimentally and statistically. When the literature was examined, it was seen that cryogenic treatment was generally applied to electrode materials, and only surface roughness and material wear amounts were examined as output parameters. The original value of the study is the interpretation of the results by applying cryogenic treatment to the test material and exploring the surface roughness and material wear amount, as well as the hole diameters and criterion diameters formed on the treated surfaces after the EDM process. As a result of the study, it was observed that the surface roughness value, the hole diameter, the amount of material wear, and the crater diameter increased with the increase in ampere and impact time. The lowest surface roughness value was 2.266 μm in the graphite electrode material at 4 amps and 200 μs impact time and the highest wear amount was realized as 0.555 g in the copper electrode material 12 amps and 400 μs impact time. The smallest hole diameter was 12.254 mm with a tuncop electrode with a pulse duration of 4 amps and 200 μs, and the lowest crater diameter was 127.301 μm with a graphite electrode at a current of 4 amps and a pulse duration of 200 μs. When the signal-to-noise ratios were examined, the optimum machining parameters for surface roughness, hole diameter, material wear amount, and crater diameter were determined as A 2 B 1 C 1 , A 1 B 3 C 3 , A 3 B 1 C 1 , and A 3 B 1 C 1 , respectively. When the ANOVA results are examined, it is determined that the most effective parameter for the surface roughness is of the current value with 86.54%, the most effective parameter for the hole diameter is the electrode material with 85.20%, the most effective parameter for material wear amount is the electrode material with 45.67% and the most effective parameter for the crater diameter is current value with 75.35%.

Eddy Current Detection of the Martensitic Transformation in AISI304 Induced upon Cryogenic Cutting

Coupled microscopic and micromagnetic depth-specific analysis of plastic deformation and phase transformation of metastable austenitic steel AISI 304L by flow forming

Method of Magnetic Control of Percentage of Ferrite and Strain-Induced Martensite in Stainless Steels

Martensitic Transformation in AISI-316 Austenitic Steel During Thermomechanical Processing

Study of martensite induced by deformation with Magnetic Barkhausen Noise Technique

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

Identification and quantification of martensite in ferritic-austenitic stainless steels and welds

Evaluation of localized mechanical properties of modified N50 welded joints at cryogenic temperature through a digital image correlation technique

Development of ANFIS model and machinability study on dry turning of cryo-treated PH stainless steel with various inserts

Detection of Microstructural Changes in Metastable AISI 347, HSS Z-M4 and Tool Steel Ferrotitanit WFN by Mechanical Loss Coefficient at Ultrasonic Frequencies

Phase-field simulation and high-temperature confocal laser scanning microscope experimental study of Martensite transformation during the disk laser quenching process

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Optical Detection of Phase Transformations in Steels: An Innovative Method for Time-Efficient Material Characterization During Tailored Thermo-mechanical Processing of a Press Hardening Steel

Microscaled Multi-frequency Eddy Current Analysis for High Throughput Characterization of Steel Micro-samples

AFM for diagnosis of nanocrystallization of steels in hardening processes

Case Study of the Tensile Fracture Investigation of Additive Manufactured Austenitic Stainless Steels Treated at Cryogenic Conditions

Measurement and Modeling of Deformation-Induced Martensitic Transformation in a Metastable Austenitic Stainless Steel under Cyclic Loadings

Electrochemically induced annealing of stainless-steel surfaces

Corrosion Initiation and Propagation on Carburized Martensitic Stainless Steel Surfaces Studied via Advanced Scanning Probe Microscopy

Experimental and statistical investigation of electro-erosion machining performance of cryogenic treated hardened AISI H13 hot work tool steel

Microstructure and mechanical properties of austenitic stainless steel welded with Co-based wires in cryogenic temperature environment