Abstract:Abstract Shale gas, as an unconventional resource, has become an exploration and exploitation hotpoint in China. In this paper, a series of experiments were conducted to investigate petrophysical and mechanical properties on the gas shales in Longmaxi Formation south Sichuan Basin, China. Mineralogical and organic geochemical analysis results indicate shale matrix shows strong heterogeneity and structure complexity. A positive correlation between TOC and quartz indicates that bioclastics are the main source of both siliciclastic and organic matters in anaerobic environment. Pore structure was investigated by mercury injection and nitrogen adsorption measurements. The dominant pore size distributes below 3.7nm measured by mercury injection, while 3-5nm by nitrogen adsorption. Micronsized fractures and nanopore structure of shale samples had been identified through mercury saturation curves and adsorption-desorption isotherms. The average maximum mercury saturation is less than 50% at 414MPa, and all of the nanopores were slit-shaped (Type H3 adsorption-desorption isotherms). The BET specific surface area which was calculated from nitrogen adsorption ranges between 7-19 m2/g and have an obvious positive relationship with TOC (total organic matter content) and illite-montmorillonite mixed layer content. Pulse decay measurement reveals that an exponential function can describe the permeability deterioration upon applied effective stress. The stress-dependent permeability of shale is more sensitive than sandstone because of high pore compressibility (low aspect ratio of pore and elastic moduli). The stress-dependent permeability data of samples with micronsized fractures can also be excellently fitted by Walsh model (fractured porous media permeability model), and fitting results show that the fractures in shale samples have high roughness and small aperture compared with sandstone. Static Young's modulus of shale samples increase with increasing quartz, and decrease with increasing TOC and clay minerals content. Due to the weak mechanical property of montmorillonite, shale samples show viscoelastic behaviour and relatively weak mechanical parameters (low Young's modulus, cohesive strengths and friction coefficients, high possion's ratio) under triaxial compression conditions. With the increasing of confining pressure, shales gradually transform from brittleness to ductileness. A comparison of static mechanical parameters between our samples and North America indicates that black siliceous shales of Longmaxi formation have moderate Young's modulus and Poisson's ratio.

Mechanical properties of organic-rich shales based on nanoindentation: A case study of deep shale gas reservoirs in Zigong area, Sichuan Basin

Assessment of the Multiphase Mechanical Properties of the Longmaxi Formation Shale Using Nanoindentation Tests

Research on the mechanical behaviour of shale based on multiscale analysis.

Probing the Mechanical Properties of Shales by Nanoindentation

Investigation of Mechanical Properties of Bedded Shale by Nanoindentation Tests: A Case Study on Lower Silurian Longmaxi Formation of Youyang Area in Southeast Chongqing, China

Application of Nanoindentation Technique in Mechanical Characterization of Organic Matter in Shale: Attentive Issues, Test Protocol, and Technological Prospect

The Mechanical Properties of Shale Based on Micro-Indentation Test

Nano-scale mechanical properties of constituent minerals in shales investigated by combined nanoindentation statistical analyses and SEM-EDS-XRD techniques

Nanoindentation investigation of mechanical and creep properties of continental Triassic Yanchang Formation shale, Ordos Basin

Characterization of meso-scale mechanical properties of Longmaxi shale using grid microindentation experiments

Loading Rate Effect on the Mechanical Behavior of Brittle Longmaxi Shale in Nanoindentation

Differences in Micromechanical Properties of Shales from Different Depositional Environment: A Case Study of Longmaxi Marine Shale and Yanchang Continental Shale Using Nanoindentation

Multiscale approach for mechanical characterization of organic-rich shale and its application

Using Nanoindentation to Characterize the Mechanical and Creep Properties of Shale: Load and Loading Strain Rate Effects

Evaluation of Petrophysical and Mechanical Features for Shale Gas Reservoirs in South Sichuan Basin, China

Multiscale Mechanical Properties of Shales: Grid Nanoindentation and Statistical Analytics

Influencing factor analysis of shale micro-indentation measurement

Microindentation analysis of mechanical properties evolution during an artificial hydrocarbon generation process

A Novel Upscaling Method for Evaluating Mechanical Properties of the Shale Oil Reservoir Based on Cluster Analysis and Nanoindentation

Coupling Grid Nanoindentation and Surface Chemical Analysis to Infer the Mechanical Properties of Shale Mineral Phases

Correlating Micromechanical Properties to Mineralogy of Shale Using Nanoindentation and Tescan Integrated Mineral Analyzer (Tima)