Abstract:For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in the presence of rubber particles because the Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that on the hydrated cement particles. Thus, the compressive strength of Rubcrete could be improved by increasing the Hamaker constant of the system. This was achieved by increasing the refractive indices of the solids (n(s)). The refractive indices of materials increase with increases in functional groups, such as OH and SH on the surface. The model provided a possible mechanism for the efficacy of treating rubber particles with NaOH in improving the compressive strength. By using NaOH solution treatment, an oxygen-containing OH group was formed on the rubber surface to increase the Hamaker constant of the system, leading to higher compressive strength. Based on this mechanism, a novel method for modification of the rubber particles was also proposed. In this process, the rubber particles were partially oxidized with hot air/steam in a fluidized bed reactor to produce the hydrophilic groups on the surface of the particles. Preliminary results obtained so far are promising in accordance with the theory.

Nano Silica and Metakaolin Effects on the Behavior of Concrete Containing Rubber Crumbs

Investigation of the Effects of Nano-Al2o3 Addition on Compatibility, Rutting and Fatigue Properties of Styrene-Butadiene-rubber Modified Asphalt

Experimental investigation into the properties of crumb rubberized concrete incorporating corrugated round steel fibers

Effect of Wollastonite Microfibers and Waste Tire Rubber on Mechanical Properties of Concrete

Influence of the Physical and Mechanical Properties of Concrete by Adding Rubber Powder and Silica Fume

Properties of Rubberized Engineered Cementitious Composites Containing Nano-Silica

Performance analysis and engineering application of waste rubber crumbs in concrete

Mechanical and microstructural characterization of sustainable concrete containing recycled concrete and waste rubber tire fiber

Evaluating the impact of nano-silica on characteristics of self-compacting geopolymer concrete with waste tire steel fiber

Mechanical and Durability Properties of Rubberized Sulfur Concrete Using Waste Tire Crumb Rubber

Thermal and Mechanical Properties of Concrete Incorporating Silica Fume and Waste Rubber Powder

Mechanical Properties and Durability Performance of Concrete Containing Calcium Carbide Residue and Nano Silica

Effects of Recycled Rubber Particles Incorporated as Partial Sand Replacement on Fresh and Hardened Properties of Cement-Based Concrete: Mechanical, Microstructural and Life Cycle Analyses

Strength, durability and shrinkage behaviours of steel fiber reinforced rubberized concrete

Experimental and numerical investigation on fracture characteristics of self-compacting concrete mixed with waste rubber particles

Pre- and post-heating mechanical properties of concrete containing recycled fine aggregate as partial replacement of natural sand and nano-silica as partial replacement of cement: experiments and predictions

Use of waste rubber as concrete additive

Investigation of the Behaviour of Concrete Containing Waste Tire Crumb Rubber

Investigation of Flexural Capacity of Concrete Containing Liquid Silicone Rubber

Mechanical Properties and Impact Resistance of Concrete Pavement Containing Crumb Rubber

Rubber/crete: Mechanical properties of scrap to reuse tire-derived rubber in concrete; A review