Abstract:Solid-state cold spray additive manufacturing has the potential to fabricate high-strength bulk high-entropy alloys (HEAs). Through systematic experiments, this study examined the microstructure and mechanical properties of cold spray fabricated bulk HEAs with mixed CoCrFeNi and Ti powders and explored the effects of Ti content in 4 and 7 at% and post-heat treatment at 800 °C/6 h and 1000 °C/6 h. It is found that the bulk HEAs are highly densified and remain nearly defect-free after the post-heat treatment. The addition of Ti serves as an mixing powder effect to further densify the alloys. Moreover, the addition of Ti and post-heat treatment promote the formation of fine precipitates, including Fe 2 Ti, Co 2 Ti, CrFe, CoTi 2 , and Ni 3 Ti, which contributes to the strengthening of the alloys. Furthermore, post-heat treatment improves the cohesion of the alloys and yields fine and relatively uniform grains by stimulating static recovery and recrystallization. These synergistic effects improve the hardness, elastic modulus, strength, and ductility properties. The average hardness and elastic modulus of the bulk alloys are as high as 377.6 HV and 94.8 GPa, respectively; the best ultimate tensile strength and elongation to failure are 626.7 MPa and 22.1 %, respectively. Synchrotron X-ray diffraction validates the complex precipitates formed and confirms that there is no phase change during tension. The study offers insights into the microstructure and mechanical properties of cold spray additive manufactured HEAs and the effects of mixed powders and post-heat treatment on tuning microstructure and properties.

Cold Spray Additive Manufacturing of CoCrFeNiMn High-Entropy Alloy: Process Development, Microstructure, and Mechanical Properties

Ultrahigh Cryogenic Strength and Exceptional Ductility in Ultrafine-Grained CoCrFeMnNi High-Entropy Alloy with Fully Recrystallized Structure

Microstructure and mechanical properties of cold spray additive manufactured and post heat treated high-entropy alloys with mixed CoCrFeNi and Ti powders

Hot cracking, crystal orientation and compressive strength of an equimolar CoCrFeMnNi high-entropy alloy printed by selective laser melting

Mechanical properties of nanostructured CoCrFeNiMn high-entropy alloy (HEA) coating

Microstructure and mechanical properties of CoCrFeNiTa high entropy alloy prepared by mechanical alloying and spark plasma sintering

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

Significant improvement of mechanical properties of cold-spray-additive manufactured FeCoNiCrMn high-entropy alloy via post-annealing

Influence of Annealing Treatment on the Microstructure and Mechanical Properties of Cold-Sprayed CoCrFeNiMn High Entropy Alloy

Cold Spray and Laser-Assisted Cold Spray of CrMnCoFeNi High Entropy Alloy Using Nitrogen as the Propelling Gas

Microstructural and Tribological Behavior of Thermal Spray CrMnFeCoNi High Entropy Alloy Coatings

Microstructure and Mechanical Behavior Comparison between Cast and Additive Friction Stir-Deposited High-Entropy Alloy Al0.35CoCrFeNi

Selective Laser Melting (SLM) Additively Manufactured CoCrFeNiMn High-Entropy Alloy: Process Optimization, Microscale Mechanical Mechanism, and High-Cycle Fatigue Behavior

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Microstructure and Corrosion Properties of AlCrFeCoNi High-Entropy Alloy Coatings Prepared by HVAF and HVOF

Microstructure and tribological properties of Al2O3 reinforced FeCoNiCrMn high entropy alloy composite coatings by cold spray

Microstructural Study of CrNiCoFeMn High Entropy Alloy Obtained by Selective Laser Melting

Microstructure of and mechanical properties of an as-cast fine-grain dual-phase Fe-based high entropy alloy formed via solid-state phase transformation

Microstructure, mechanical properties and corrosion resistance of an as-cast fine-structured Cr-Fe-Ni-Al-Si high entropy alloy

MICROSTRUCTURE AND PROPERTIES OF COATING OF AlFeCrNiMo HIGH-ENTROPY ALLOY

Microstructure and Properties of NiCoCrAlTi High Entropy Alloy Prepared Using MA-SPS Technique