Abstract:The required drying time and length for electrode production can be reduced significantly by the application of multistage drying profiles using infrared radiation, without deterioration of electrode properties. Evidence is demonstrated by adhesion measurements, which provide insight into the component distribution within the electrode and electrochemical characterization in pouch cell tests for various process routes with aqueous‐processed graphite anodes. The drying of solvent‐processed electrodes is a critical process step in the manufacturing of lithium‐ion batteries. The technology used to introduce the energy required for drying into the material, combined with the specified process parameters, significantly influences the resulting electrode properties. A major challenge is to counteract binder migration effects that may occur during drying of the porous electrode structure, causing a decrease in adhesion and electrochemical performance, especially for high drying rates. From this motivation, investigations on the influence of process design during near‐infrared drying of aqueous‐processed graphite anodes are carried out. A multistage drying design with varying parameters in specific drying sections with energy input by radiation is applied. The results show that the specific application of a three‐stage drying profile in combination with energy input by radiation enables a significant decrease in drying time by at least 60% while the electrode properties can be preserved. These findings indicate a beneficial development of binder distribution as a consequence of multistage NIR drying, evidenced by adhesion and electrochemical performance. Finally, the application of the multistage drying profile is theoretically transferred to an industrial‐scale roll‐to‐roll dryer, whereby the necessary dryer length can be reduced by 53%.

Investigation of Drying Curves of Lithium‐Ion Battery Electrodes with a New Gravimetrical Double‐Side Batch Dryer Concept Including Setup Characterization and Model Simulations

Modeling and Analysis of the Drying Process of Lithium-Ion Battery Electrodes Based on Non-Steady-State Drying Kinetics

Microstructure formation of lithium-ion battery electrodes during drying – An ex-situ study using cryogenic broad ion beam slope-cutting and scanning electron microscopy (Cryo-BIB-SEM)

Application of Multistage Drying Profiles for Accelerated Production of Li‐Ion Battery Anodes Using Infrared Radiation: Validation with Electrochemical Performance and Structural Properties

Experimental Analysis of Drying Kinetics and Quality Aspects of Convection-Dried Cathodes at Laboratory Scale

Delamination behavior of lithium-ion battery anodes: Influence of drying temperature during electrode processing

Drying of Lithium‐Ion Battery Anodes for Use in High‐Energy Cells: Influence of Electrode Thickness on Drying Time, Adhesion, and Crack Formation

Binder migration during drying of lithium-ion battery electrodes: modelling and comparison to experiment

Modeling and Optimizing the Drying Process of Electrode Manufacturing for Lithium‐Ion Batteries

A Review of Lithium‐Ion Battery Electrode Drying: Mechanisms and Metrology

A Computational Fluid Dynamics–Discrete Element Method Model for Physics‐Based Simulation of Structure Formation during Battery Electrode Drying

Mechanical and Electrochemical Implications of Drying Temperature on Lithium‐Ion Battery Electrodes

2D Discrete Element Simulation of Electrode Structural Evolutions in Li‐Ion Battery During Drying and Calendering

In-line monitoring of a multi-stage drying process for battery electrodes: vol. 1—applying methods of scattered light measurement

Investigation on Heat and Mass Transfer in Spray Drying Process

Fundamental investigation on drying rates of cathodes and separators for sulfide-based all-solid-state batteries

Identification of Cause–Effect Relationships between Process Parameters and the Film Formation in the Semidry Electrode Production for Lithium‐Ion Batteries

Coarse-grained molecular dynamics simulations of microstructure evolution and debonding in water-based cathode electrode drying

DEM Simulations of the Calendering Process: Parameterization of the Electrode Material of Lithium-Ion Batteries

Experimental investigation of the multi-layer wetting behavior of electrode-separator-composites in lithium-ion batteries

Simulation of Micro/Nanopowder Mixing Characteristics for Dry Spray Additive Manufacturing of Li-Ion Battery Electrodes