Abstract:ZrO2–Y2O3 ceramic coatings were deposited on AISI 304 stainless steel by both a low-pressure plasma spraying (LPPS) and a laser-assisted plasma hybrid spraying (LPHS). Microstructure and tribological characteristics of ZrO2–Y2O3 coatings were studied using an optical microscope, a scanning electron microscope, and an SRV high-temperature friction and wear tester. The LPHS coatings exhibit distinctly reduced porosity, uniform microstructure, high hardness and highly adhesive bonding, although more microcracks and even vertical macrocracks seem to be caused in the LPHS coatings. The ZrO2 lamellae in the LPHS coatings before and after 800°C wear test consist mainly of the metastable tetragonal (t′) phase of ZrO2 together with small amount of c phase. The t′ phase is very stable when it is exposed to the wear test at elevated temperatures up to 800°C for 1 h. The friction and wear of the LPHS coatings shows a strong dependence on temperature, changing from a low to a high wear regime with the increase of temperature. At low temperatures, friction and wear of the LPHS coatings is improved by laser irradiation because of the reduced connected pores and high hardness in contrary to the LPPS coating. However, at elevated temperatures, the friction and wear of the LPHS coatings is not reduced by laser irradiation. At room temperature, mild scratching and plastic deformation of the LPHS coatings are the main failure mechanism. However, surface fatigue, microcrack propagation, and localized spallation featured by intersplat fracture, crumbling and pulling-out of ZrO2 splats become more dominated at elevated temperatures.

Improving wear resistance of plasma-sprayed calcia and magnesia-stabilized zirconia mixed coating: roles of phase stability and microstructure

Preparation and properties of nano ZrO2 coating on magnesium alloy

Improvement of the Tribological Properties of Alumina Coatings by Zirconia Addition

Microstructure characterization of in-situ ZrC composite coating with graceful toughness and improved tribological properties prepared by plasma spraying

Study on Plasma Sprayed 40%Zro_2-Al_2o_3-13%tio_2 Ceramic Coatings and Tribological Properties

Microstructure of plasma-sprayed Al2O3-ZrO 2 composite coatings

Zirconia-based Abradable Coatings Fabricated on Single-Crystal Superalloy: Microstructure, Residual Stress and Mechanical Properties

Microstructure and Properties of Al2O3–ZrO2–Y2O3 Composite Coatings Prepared by Plasma Spraying

Microstructure and abrasive resistance of ZrO2-MoSi2 coatings deposited by supersonic plasma spraying

Mechanical Properties of Nanostructured Zirconia Coatings Fabricated by Air Plasma Spraying

Microstructure Characteristics and Ablation Behavior of an Al1.92 Cr0.08 O3-SiC-ZrC Anti-Ablation Coating

Microstructure and tribological characteristics of ZrO2–Y2O3 ceramic coatings deposited by laser-assisted plasma hybrid spraying

Characterization of the Near-Eutectic Al2O3–40 Wt% ZrO2Composite Coating Fabricated by Atmospheric Plasma Spray. Part II: Microstructure and Mechanical Properties of Nanocomposite Coating

A Study of Parameters Affecting Wear Resistance of Alumina and Yttria Stabilized Zirconia Composite Coatings on Al-6061 Substrate

Microstructure and Wear Behaviors of Plasma-Sprayed MoAlB Ceramic Coating

Characterization of the Near-Eutectic Al<sub>2</sub>O<sub>3</sub>–40 wt% ZrO<sub>2</sub>Composite Coating Fabricated by Atmospheric Plasma Spray. Part II: Microstructure and Mechanical Properties of Nanocomposite Coating

Effect of Nano-Si3N4 Additives and Plasma Treatment on the Dry Sliding Wear Behavior of Plasma Sprayed Al2O3-8YSZ Ceramic Coatings

Microstructure and Oxidation Property of CrSi2-ZrSi2-Y2O3/SiC Coating Prepared on C/C Composites by Supersonic Atmosphere Plasma Spraying

Preparation and characterization of supersonic plasma sprayed Al–Al2O3–Cr2O3 composite coatings on magnesium alloy substrate

Friction and Wear Assessment of Yttria Stabilised Zirconia Thermal Barrier Coatings Produced by Plasma Spraying Method