Abstract:Semi-solid thixoforming processes rely on a material microstructure made of globular solid grains more or less connected to each other, thus developing a solid skeleton deforming into a liquid phase. During processing, the material structure changes with the processing history due to the agglomeration of the particles and the breaking of the grains bonds. This particular evolutive microstructure makes semi-solid materials behave as solids at rest and as liquids during shearing, which causes a decrease of the viscosity and of the resistance to deformation while shearing. Thixoforming of aluminum and magnesium alloys is state of the art and a growing number of serial production lines are in operation all over the world. But there are only few applications of semi-solid processing of higher melting point alloys such as steel. This can partly be attributed to the high forming temperature combined with the intense high temperature corrosion that requires new technical solutions. However the semi-solid forming of steels reveals high potential to reduce material as well as energy consumption compared to conventional process technologies, such as casting and forging. Simulation techniques exhibit a great potential to acquire a good understanding of the semi-solid material process. Therefore, this work deals with the development of an appropriate constitutive model for semi-solid thixoforming of steel. The constitutive law should be able to simulate the complex rheology of semi-solid materials, under both steady-state and transient conditions. For example, the peak of viscosity at start of a fast loading should be reproduced. The use of a nite yield stress is appropriate because a vertical billet does not collapse under its own weight unless the liquid fraction is too high. Furthermore, this choice along with a non-rigid solid formalism allows predicting the residual stresses after cooling down to room temperature. Several one-phase material modeling have been proposed and are compared. Thermomechanical modeling using a thermo-elasto-viscoplastic constitutive law has been developed. The basic idea is to extend the classical isotropic hardening and viscosity laws to the non solid state by considering two non-dimensional internal parameters. The rst internal parameter is the liquid fraction and depends on the temperature only. The second one is a structural parameter that characterizes the degree of structural build up in the microstructure. Those internal parameters can depend on each other. The internal parameters act on the the viscosity law and on the yield surface evolution law. Di erent formulations of viscosity and hardening laws have been proposed and are compared to each other. In all cases, the semi-solid state is treated as a particular case, and the constitutive modeling remains valid over the whole range of temperature, starting from room temperature to above the liquidus. These models are tested and illustrated by mean of several representative numerical applications.

Thermodynamic Modeling of Liquid Steel

Phase Field Simulation for Non-Isothermal Solidification of Multicomponent Alloys Coupled with Thermodynamics Database

Aluminum Deoxidation Equilibria in Liquid Iron: Part II. Thermodynamic Modeling

THERMODYNAMIC MODELING OF PHASE EQUILIBRIA AT STEEL ALLOYED WITH MANGANESE AND CHROME

THERMODYNAMICS OF THE PROCESSES OF INTERACTION OF LIQUID METAL COMPONENTS IN Fe – Mg – Al – La – O SYSTEM

Thermodynamics of the Interactions in Fe–Mg–Al–La–O Melts

Rapid Solidification of Non-Stoichiometric Intermetallic Compounds: Modeling and Experimental Verification

Application and assessment of aluminium deoxidation equilibria in liquid steel using various formalisms based on some statistical thermodynamic models

Thermodynamic Evaluation of Inclusion Formation during Cooling and Solidification of Low Carbon Si-Mn Killed Steel

Thermodynamic Modeling of Solid Flux Interactions with Molten Aluminum

Aluminum Deoxidation Equilibria in Liquid Iron: Part III—Experiments and Thermodynamic Modeling of the Fe-Mn-Al-O System

The use of computational thermodynamics for the determination of surface tension and Gibbs–Thomson coefficient of multicomponent alloys

A Cellular Automaton Technique for the Modeling of Solidification Microstructure in Multi-Component Alloys

Thermodynamic Description of Multi-Component Multi-Phase Alloys and Its Application to the Solidification Process

Thermodynamic modelling of liquid slag-matte-metal equilibria applied to the simulation of the Peirce-Smith converter

Modelling Of The Thermosolutal Convection And Macrosegregation In The Solidification Of An Fe-C Binary Alloy

Semi-solid constitutive modeling for the numerical simulation of thixoforming processes.

Calculation of Physical Properties for Use in Models of Continuous Casting Process-Part 2: Steels

Three-dimensional simulation of thermosolutal convection and macrosegregation in steel ingots

The High-Temperature Cu-Fe-S System: Thermodynamic Analysis and Prediction of the Liquid–Solid Phase Range

Modeling of Ladle Refining Process Considering Mixing and Chemical Reaction