Abstract:The stochastic morphology of ceramic foams and discrepancies between specimens of the same type complicate the creation of numerical models during the design and optimization of porous medium burners. A favourable solution, from the modelling point of view, is the application of an ordered diamond lattice with definite geometry produced by means of additive manufacturing, which potentially allows achieving higher efficiencies and lower pollutant emissions. This document, describes procedures in the selection of diamond lattices with proper parameters and the comparison of the porous medium burner performances with different materials and geometries. The first section explains our methodology for geometrical analysis of ceramic foams and further selection of equivalent diamond lattices. Three acquired types of ceramic SiSiC foams (10 PPI, 30 PPI, and 60 PPI) were evaluated from image cross-sections and digital replicas that were obtained by means of X-ray computed tomography. Upon investigating, we found that pore sizes provided by a manufacturer were underestimated and discrepancies between them reached up to 100% for 60 PPI specimens. Combination of adapted cell size analysis according to ASTM D3576-15 standard and a developed tetrakaidecahedron model was favoured among other methods of pore size determination. After analysis of ceramic foams, an approach of selecting equivalent diamond lattices in terms of porosity and absolute permeability was proposed. As a result, three specimens were printed from CoCr alloy: 10 PPI and 60 PPI foams, as well as an equivalent 10 PPI diamond lattice. A test bench of the two-section porous medium burner was designed and assembled, which allowed the temperature, pollutant emissions and pressure drop measurements. The second section describes the experimental procedures and results from six different setups that compared the foam and diamond lattice geometries, and compared ceramic and metal as materials. In all setups, pollutant emissions were low and at the detection limit of the equipment, which agrees with theory and previous research. The application of CoCr material was determined as advantageous in the upstream section, ensuring higher flame stability and structural strength. A diamond lattice was found to be a good candidate for replacement of the foam geometry by providing both the predictability and higher structural stiffness. We recommend that further research should be done on using diamond lattice geometries with CoCr alloy in the upstream section, and SiSiC ceramic foam in the downstream section for the broad range of lean combustion regimes.

Effects of the internal structures of monolith ceramic substrates on thermal and hydraulic properties: additive manufacturing, numerical modelling and experimental testing

Additive Manufacturing of Novel Hybrid Monolithic Ceramic Substrates

Thermal and structural performance of additively manufactured ceramic porous media burners

Design of porous medium burners by means of additive manufacturing

Numerical Simulation of Sintering of DLP Printed Alumina Ceramics

Additive Manufacturing of Liquid-cooled Ceramic Heat Sinks: An Experimental and Numerical Study

Application of Ceramic Lattice Structures to Design Compact, High Temperature Heat Exchangers: Material and Architecture Selection

Pure copper extrusion additive manufacturing of lattice structures for enabling enhanced thermal efficiency in hydrogen production

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties

Effects of different cross-sections of Body Centered Cubic cells on pressure drop and heat transfer of additively manufactured heat sinks

Energy-Reduced Fabrication of Light-Frame Ceramic Honeycombs by Replication of Additive Manufactured Templates

Tailoring Thermal Insulation Architectures from Additive Manufacturing

Fabrication of High Thermal Conductivity Aluminum Nitride Ceramics via Digital Light Processing 3D Printing

Structure design influencing the mechanical performance of 3D printing porous ceramics

Experimental and numerical analysis of the thermal performance of PCM-impregnated reticular structures obtained by additive manufacturing

Effects of the manufacturing process on the flexural properties of EBMed lattice structures

Effect of heat treatment on compression properties of the 316L diamond structure fabricated through selective laser melting

Improving contact resistance in metal–ceramic heat exchangers running liquid metal by additive manufacturing and ceramic tubes with electroplated films

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

A Cost-Efficient Fabrication Strategy for Conductive Ti2alc Honeycomb Monolith Using Elemental Powders

Unravelling the Influence of Binder Typology during the Additive Manufacturing of Hybrid Multi-Channel Cylinders for Catalytic Purposes