Abstract:Abstract The goal of this work is to predict the effect of part geometry and process parameters on the instantaneous spatiotemporal distribution of temperature, also called the thermal field or temperature history, in metal parts as they are being built layer-by-layer using additive manufacturing (AM) processes. In pursuit of this goal, the objective of this work is to develop and verify a graph theory-based approach for predicting the temperature distribution in metal AM parts. This objective is consequential to overcome the current poor process consistency and part quality in AM. One of the main reasons for poor part quality in metal AM processes is ascribed to the nature of temperature distribution in the part. For instance, steep thermal gradients created in the part during printing leads to defects, such as warping and thermal stress-induced cracking. Existing nonproprietary approaches to predict the temperature distribution in AM parts predominantly use mesh-based finite element analyses that are computationally tortuous—the simulation of a few layers typically requires several hours, if not days. Hence, to alleviate these challenges in metal AM processes, there is a need for efficient computational models to predict the temperature distribution, and thereby guide part design and selection of process parameters instead of expensive empirical testing. Compared with finite element analyses techniques, the proposed mesh-free graph theory-based approach facilitates prediction of the temperature distribution within a few minutes on a desktop computer. To explore these assertions, we conducted the following two studies: (1) comparing the heat diffusion trends predicted using the graph theory approach with finite element analysis, and analytical heat transfer calculations based on Green’s functions for an elementary cuboid geometry which is subjected to an impulse heat input in a certain part of its volume and (2) simulating the laser powder bed fusion metal AM of three-part geometries with (a) Goldak’s moving heat source finite element method, (b) the proposed graph theory approach, and (c) further comparing the thermal trends predicted from the last two approaches with a commercial solution. From the first study, we report that the thermal trends approximated by the graph theory approach are found to be accurate within 5% of the Green’s functions-based analytical solution (in terms of the symmetric mean absolute percentage error). Results from the second study show that the thermal trends predicted for the AM parts using graph theory approach agree with finite element analyses, and the computational time for predicting the temperature distribution was significantly reduced with graph theory. For instance, for one of the AM part geometries studied, the temperature trends were predicted in less than 18 min within 10% error using the graph theory approach compared with over 180 min with finite element analyses. Although this paper is restricted to theoretical development and verification of the graph theory approach, our forthcoming research will focus on experimental validation through in-process thermal measurements.

Efficient thermal simulation of large-scale metal additive manufacturing using hot element addition

FAST COMPUTATION OF THERMAL FIELD OF DIRECT METAL DEPOSITION: A PRELIMINARY STUDY BASED ON QUIET ELEMENT METHOD

Heat Source Modeling and Residual Stress Analysis for Metal Directed Energy Deposition Additive Manufacturing

Temporally continuous thermofluidic-thermomechanical modeling framework for metal additive manufacturing

Thermal Modeling in Metal Additive Manufacturing Using Graph Theory

Thermal Analysis for Simulation of Metal Additive Manufacturing Process Considering Temperature- and History-Dependent Material Properties

Numerical Simulation Development and Computational Optimization for Directed Energy Deposition Additive Manufacturing Process

Thermal simulation of wire arc additive manufacturing: a new material deposition and heat input modelling

A highly efficient computational approach for fast scan-resolved simulations of metal additive manufacturing processes on the scale of real parts

Thermal Field Prediction for Welding Paths in Multi-Layer Gas Metal Arc Welding-Based Additive Manufacturing: A Machine Learning Approach

A numerical model-based deposition strategy for heat input regulation during plasma arc-based additive manufacturing

Computational Modelling of Metal Additive Manufacturing

Efficient reduced-order thermal modelling of scanning laser melting for additive manufacturing

Modeling Melt Pool Geometry in Metal Additive Manufacturing Using Goldak's Semi-Ellipsoidal Heat Source: A Data-driven Computational Approach

A computationally efficient thermo-mechanical model for wire arc additive manufacturing

On phase change and latent heat models in metal additive manufacturing process simulation

An Efficient and High-Fidelity Local Multi-Mesh Finite Volume Method for Heat Transfer and Fluid Flow Problems in Metal Additive Manufacturing

Computational thermal multi-phase flow for metal additive manufacturing

A Heat Transfer Finite Element Model for Wire-Arc-Additive-Manufacturing Process

A highly efficient computational approach for part-scale microstructure predictions in Ti-6Al-4V additive manufacturing

Thermo-Mechanical Modeling of Wire-Fed Electron Beam Additive Manufacturing