Abstract:Abstract The goal of this work is to predict the effect of part geometry and process parameters on the instantaneous spatiotemporal distribution of temperature, also called the thermal field or temperature history, in metal parts as they are being built layer-by-layer using additive manufacturing (AM) processes. In pursuit of this goal, the objective of this work is to develop and verify a graph theory-based approach for predicting the temperature distribution in metal AM parts. This objective is consequential to overcome the current poor process consistency and part quality in AM. One of the main reasons for poor part quality in metal AM processes is ascribed to the nature of temperature distribution in the part. For instance, steep thermal gradients created in the part during printing leads to defects, such as warping and thermal stress-induced cracking. Existing nonproprietary approaches to predict the temperature distribution in AM parts predominantly use mesh-based finite element analyses that are computationally tortuous—the simulation of a few layers typically requires several hours, if not days. Hence, to alleviate these challenges in metal AM processes, there is a need for efficient computational models to predict the temperature distribution, and thereby guide part design and selection of process parameters instead of expensive empirical testing. Compared with finite element analyses techniques, the proposed mesh-free graph theory-based approach facilitates prediction of the temperature distribution within a few minutes on a desktop computer. To explore these assertions, we conducted the following two studies: (1) comparing the heat diffusion trends predicted using the graph theory approach with finite element analysis, and analytical heat transfer calculations based on Green’s functions for an elementary cuboid geometry which is subjected to an impulse heat input in a certain part of its volume and (2) simulating the laser powder bed fusion metal AM of three-part geometries with (a) Goldak’s moving heat source finite element method, (b) the proposed graph theory approach, and (c) further comparing the thermal trends predicted from the last two approaches with a commercial solution. From the first study, we report that the thermal trends approximated by the graph theory approach are found to be accurate within 5% of the Green’s functions-based analytical solution (in terms of the symmetric mean absolute percentage error). Results from the second study show that the thermal trends predicted for the AM parts using graph theory approach agree with finite element analyses, and the computational time for predicting the temperature distribution was significantly reduced with graph theory. For instance, for one of the AM part geometries studied, the temperature trends were predicted in less than 18 min within 10% error using the graph theory approach compared with over 180 min with finite element analyses. Although this paper is restricted to theoretical development and verification of the graph theory approach, our forthcoming research will focus on experimental validation through in-process thermal measurements.

Modeling Melt Pool Geometry in Metal Additive Manufacturing Using Goldak's Semi-Ellipsoidal Heat Source: A Data-driven Computational Approach

A Gaussian Process-Based extended Goldak heat source model for finite element simulation of laser powder bed fusion additive manufacturing process

Thermo-Fluid-Dynamic Modeling of the Melt Pool During Selective Laser Melting for AZ91D Magnesium Alloy

Heat Source Modeling and Residual Stress Analysis for Metal Directed Energy Deposition Additive Manufacturing

Investigation of Melt Pool Geometry Control in Additive Manufacturing Using Hybrid Modeling

Accurate prediction of melt pool shapes in laser powder bed fusion by the non-linear temperature equation including phase changes - isotropic versus anisotropic conductivity

Efficient thermal simulation of large-scale metal additive manufacturing using hot element addition

Thermal Modeling in Metal Additive Manufacturing Using Graph Theory

Computational Study of Transport Phenomena in Laser Melting-Based Metal Additive Manufacturing

Developing the AM G-code based thermomechanical finite element platform for the analysis of thermal deformation and stress in metal additive manufacturing process

On the importance of heat source model determination for numerical modeling of selective laser melting of IN625

Evaporation Model for Keyhole Dynamics During Additive Manufacturing of Metal

Development of a Comprehensive Model for Predicting Melt Pool Characteristics with Dissimilar Materials in Selective Laser Melting Processes

Predicting and correlating melt pool characteristics with processing parameters in IN625 powder bed fusion additive manufacturing

A novel smoothed particle hydrodynamics formulation for thermo-capillary phase change problems with focus on metal additive manufacturing melt pool modeling

Thermal Analysis for Simulation of Metal Additive Manufacturing Process Considering Temperature- and History-Dependent Material Properties

Lattice Boltzmann Simulation of Metallic Powder Melting During Additive Manufacturing

Spatiotemporal Monitoring of Melt-Pool Variations in Metal-Based Additive Manufacturing

Heat transfer model and finite element formulation for simulation of selective laser melting

A New Heat Transfer Simulation Model for Selective Laser Melting to Estimate the Geometry of Cross Section of Melt Pool

A numerical model-based deposition strategy for heat input regulation during plasma arc-based additive manufacturing