Abstract:Ammonia, as an alternative fuel for internal combustion engines, can achieve nearly zero carbon emissions. Although the development of the pure ammonia engine is limited by its poor combustion characteristics, ammonia–hydrocarbon mixed combustion can effectively improve the combustion of ammonia fuel. With the increase in the ammonia fuel proportion in the fuel mixture, a large number of nitrogen oxides (NOX) and unburned ammonia may be discharged, which have a poor impact on the environment. In this study, the performance of selective catalytic reduction (SCR) aftertreatment technology in reducing NOX and ammonia emissions from ammonia–diesel dual-fuel engines was investigated using simulation. A good cross-dimensional model was established under the coupling effect, though the effect of a single-dimensional model could not be presented. The results show that when the exhaust gas in the engine cylinder is directly introduced into the SCR without additional reducing agents such as urea, unburned ammonia flowing into SCR model is in excess, and there will be only ammonia at the outlet; however, if the unburned ammonia fed into the SCR model is insufficient to reduce NO, the ammonia concentration at the outlet will be 0. NOX can be 100% effectively reduced to N2 under most engine conditions; thus, unburned ammonia in exhaust plays a role in reducing NOX emissions from ammonia–diesel dual-fuel engines. However, when the concentration of unburned ammonia in the exhaust gas of an ammonia–diesel dual-fuel engine is large, its ammonia emissions are still high even after the SCR. In addition, the concentrations of N2O after SCR do not decrease, but increase by 50.64 in some conditions, the main reason for which is that by the action of the SCR catalyst, NO2 is partially converted into N2O, resulting in an increase in its concentration at the SCR outlet. Adding excessive air or oxygen into the SCR aftertreatment model can not only significantly reduce the ammonia concentration at the outlet of the model without affecting the NOX conversion efficiency of SCR, but inhibit N2O production to some extent at the outlet, thus reducing the unburned ammonia and NOX emissions in the tail gas of ammonia–diesel dual-fuel engines at the same time without the urea injection. Therefore, this study can provide theoretical guidance for the design of ammonia and its mixed-fuel engine aftertreatment device, and provide technical support for reducing NOX emissions of ammonia and its mixed fuel engines.

Modeling and Optimization of Multi-functional Ammonia Slip Catalysts for Diesel Exhaust Aftertreatment

Modeling and Analysis of Ammonia Oxidation and Nitrous Oxide Formation on a Dual-Layer Ammonia Slip Catalyst for Diesel After-Treatment

The Reactions and Role of Ammonia Slip Catalysts in Modern Urea-SCR Systems

A Modeling Study of NH3 Slip Catalysts: Analysis of the SCR/PGM Interactions

Robust, Model-Based Urea Dosing Control for SCR Aftertreatment Systems using a Cross-Sensitive Tailpipe NOx Sensor

Fluid Mixing Optimization Strategy of Catalytic Reactor for Marine SCR System

Ammonia Dynamic Modelling over Cu-SSZ-13 Catalyst for NOx Emission Control in Diesel Vehicles

Ammonia storage and slip under steady and transient state in close-coupled SCR

Applied Catalysis in the Automotive Industry: Development of a Commercial Diesel Oxidation Catalyst Simulation Model Balanced for the Requirements of an Original Engine Manufacturer. Part 1, NOx Chemistry

Nitrogen Oxides and Ammonia Removal Analysis Based on Three-Dimensional Ammonia-Diesel Dual Fuel Engine Coupled with One-Dimensional SCR Model

Enhancement of the Ammonia Kinetic Mechanism for Nitrogen-Based Pollutant Chemistry

Applying Separate Treatment of Fuel- and Air-Borne Nitrogen to Enhance Understanding of In-Cylinder Nitrogen-Based Pollutants Formation and Evolution in Ammonia-Diesel Dual Fuel Engines

Tuning the Standard SCR Reaction Kinetics to Model NO Conversion in a Diesel Engine Exhaust SCR Catalyst System Under Steady State Conditions in 1D and 3D Geometries Using Ammonia Gas as the Reductant

Designing a Bifunctional Pt/Cu-SSZ-13 Catalyst for Ammonia-Selective Catalytic Oxidation with Superior Selectivity

Modeling and Performance Analysis of SCR DeNOx Catalyst for Reducing NOx Emissions in Diesel Engine

Experimental Study of Aftertreatment System Configurations for Euro Ⅵ Heavy-Duty Diesel Engines

Multi-Scale SCR Modeling, 1D Kinetic Analysis and 3D System Simulation

Ammonia storage and slip in a urea selective catalytic reduction catalyst under steady and transient conditions

Potential Risk of NH3 Slip Arisen from Catalytic Inactive Site in Selective Catalytic Reduction of NOx with Metal-Free Carbon Catalysts

Design Strategies for High-Performance NH 3 -SCO Catalysts: Identifying and Modulating Direct Anchoring Sites for Ag on TiO 2

Selective Noncatalytic Reduction of NO x Using Ammonium Sulfate