Abstract:Multiple remanufacturing methods for recycled carbon fiber reinforced composites. Considering the types of carbon fiber reinforced polymer (CFRP) waste and the length of recycled carbon fiber (rCF), it is still a challenge to obtain high‐performance rCF and realize its high‐value reuse. In this paper, rCF was obtained by the thermal activated oxide semiconductor, and the effects of temperature and time on the resin decomposition rate of CFRP with different resin systems were analyzed. Three remanufacturing processes, namely wet fiber alignment (WFA), direct ink writing (DIW) and fused deposition modeling (FDM), were used to remanufacture rCF in millimeter and micron scale into recycled carbon fiber reinforced polymer (rCFRP) and the effects of rCF content on the mechanical properties of rCFRP were studied. The results showed that the optimal recycling parameter for EP‐EDA is 520°C, 45 min, and for EP‐MeTHPA and phenolic resin, the optimal recycling parameter is 520°C, 35 min. With the increase of rCF content, the tensile strength and modulus of WFA, DIW and FDM samples all increased to varying degrees. When the rCF content is 15 wt%, the tensile strength of WFA, DIW and FDM samples is increased by 355.6%, 68.4%, and 34.5%, respectively, compared with the corresponding pure resin samples. The mechanical properties of WFA, DIW and FDM samples are greatly different due to the rCF content, rCF length, interface bonding and alignment of rCF. This paper emphasizes the important effects of remanufacturing process, material composition and rCF content on the properties of rCFRP, and provides multiple ways for high‐value reuse of rCF. Highlights rCF obtained by thermal activated oxide semiconductor. Resin decomposition rate of CFRP waste with different resin systems. Multiple remanufacturing processes for rCF. Effects of rCF content and material composition on the properties of rCFRP.

Investigation of the flexural and impact strength of recycled carbon fiber (RCF) I polyester composite

Investigation of the resin infusion process and mechanical performance of carbon fiber reinforced plastic composites from recycled carbon fiber

Carbon fibers recovery from CFRP recycling process and their usage: A review

Investigation of recycling effects on the mechanical properties of short carbon and glass fiber reinforced polyetherimide composites

Recycled carbon fiber potential for reuse in carbon fiber/PA6 composite parts

Investigation on Stress Relaxation of Discontinuous Recycled Carbon Fiber Composites

Performance analysis of recycled carbon fiber under recycling process parameters optimized using response surface methodology

Carbon Fiber Reinforced Recycled Polypropylene/Polyolefin Elastomer Composites with High Mechanical Properties

Efficient and Sustainable Strategy for Recycling of Carbon Fiber-Reinforced Thermoset Composite Waste at Ambient Pressure

Recycled carbon fiber reinforced composites: Enhancing mechanical properties through co-functionalization of carbon nanotube-bonded microfibrillated cellulose

An Experimental Study on Mechanical Behaviors of Carbon Fiber and Microwave-Assisted Pyrolysis Recycled Carbon Fiber-Reinforced Concrete

Pretreating Recycled Carbon Fiber Nonwoven with a Sizing Formulation to Improve the Performance of Thermoplastic Recycled Fiber-Reinforced Composites

Experimental Investigation into the Mechanical and Piezoresistive Sensing Properties of Recycled Carbon-Fiber-Reinforced Polymer Composites for Self-Sensing Applications

Study on recycled carbon fiber obtained by thermal activated oxide semiconductor and mechanical properties of its reinforced polymer composites

Biocomposite Innovation: Assessing Tensile and Flexural Performance with Maleated Natural Rubber Additives

Carbon-Fiber-Recycling Strategies: A Secondary Waste Stream Used for PA6,6 Thermoplastic Composite Applications

A Study to Investigate the Mechanical Properties of Recycled Carbon Fibre/Glass Fibre-Reinforced Epoxy Composites Using a Novel Thermal Recycling Process

High-Efficiency Carbon Fiber Recovery Method and Characterization of Carbon FIBER-Reinforced Epoxy/4,4′-Diaminodiphenyl Sulfone Composites

Mechanical performance of modified Polypropylene/Polyamide matrix reinforced with treated recycled carbon fibers for lightweight applications

Research on Microwave Pyrolysis Recovery and Reuse Performance of Carbon Fiber Composites

Exploratory Study of Flexural Performance of Mechanically Recycled Glass Fiber Reinforced Polymer Shreds as Reinforcement in Cement Mortar