Abstract:Multiple remanufacturing methods for recycled carbon fiber reinforced composites. Considering the types of carbon fiber reinforced polymer (CFRP) waste and the length of recycled carbon fiber (rCF), it is still a challenge to obtain high‐performance rCF and realize its high‐value reuse. In this paper, rCF was obtained by the thermal activated oxide semiconductor, and the effects of temperature and time on the resin decomposition rate of CFRP with different resin systems were analyzed. Three remanufacturing processes, namely wet fiber alignment (WFA), direct ink writing (DIW) and fused deposition modeling (FDM), were used to remanufacture rCF in millimeter and micron scale into recycled carbon fiber reinforced polymer (rCFRP) and the effects of rCF content on the mechanical properties of rCFRP were studied. The results showed that the optimal recycling parameter for EP‐EDA is 520°C, 45 min, and for EP‐MeTHPA and phenolic resin, the optimal recycling parameter is 520°C, 35 min. With the increase of rCF content, the tensile strength and modulus of WFA, DIW and FDM samples all increased to varying degrees. When the rCF content is 15 wt%, the tensile strength of WFA, DIW and FDM samples is increased by 355.6%, 68.4%, and 34.5%, respectively, compared with the corresponding pure resin samples. The mechanical properties of WFA, DIW and FDM samples are greatly different due to the rCF content, rCF length, interface bonding and alignment of rCF. This paper emphasizes the important effects of remanufacturing process, material composition and rCF content on the properties of rCFRP, and provides multiple ways for high‐value reuse of rCF. Highlights rCF obtained by thermal activated oxide semiconductor. Resin decomposition rate of CFRP waste with different resin systems. Multiple remanufacturing processes for rCF. Effects of rCF content and material composition on the properties of rCFRP.

Performance analysis of recycled carbon fiber under recycling process parameters optimized using response surface methodology

Study on recycled carbon fiber obtained by thermal activated oxide semiconductor and mechanical properties of its reinforced polymer composites

A Novel Approach on Recycling Short-Chopped Carbon Fibers by Electric Field Induced Manipulation

Efficient and Sustainable Strategy for Recycling of Carbon Fiber-Reinforced Thermoset Composite Waste at Ambient Pressure

Research on a two-step pyrolysis-oxidation process of carbon fiber-reinforced epoxy resin-based composites and analysis of product properties

Efficient recycling of carbon fibers from amine-cured CFRP composites under facile condition

Facile preparation, closed-loop recycling of multifunctional carbon fiber reinforced polymer composites

A Study to Investigate the Mechanical Properties of Recycled Carbon Fibre/Glass Fibre-Reinforced Epoxy Composites Using a Novel Thermal Recycling Process

Optimisation of recycling process parameters of carbon fibre in epoxy matrix composites

Study on oxidation behavior during process of recycling carbon fibers from CFRP by pyrolysis

Investigation of the resin infusion process and mechanical performance of carbon fiber reinforced plastic composites from recycled carbon fiber

Recycling and Reutilization of Waste Carbon Fiber Reinforced Plastics: Current Status and Prospects

An Experimental Study on Mechanical Behaviors of Carbon Fiber and Microwave-Assisted Pyrolysis Recycled Carbon Fiber-Reinforced Concrete

Machine learning constructs the microstructure and mechanical properties that accelerate the development of CFRP pyrolysis for carbon-fiber recycling

High-Efficiency Carbon Fiber Recovery Method and Characterization of Carbon FIBER-Reinforced Epoxy/4,4′-Diaminodiphenyl Sulfone Composites

Efficient method of recycling carbon fiber from the waste of carbon fiber reinforced polymer composites

Thermal Recycling Process of Carbon Fibers from Composite Scrap—Characterization of Pyrolysis Conditions and Determination of the Quality of Recovered Fibers

Characterization of carbon fibers recovered through mechanochemical-enhanced recycling of waste carbon fiber reinforced plastics

Research on Microwave Pyrolysis Recovery and Reuse Performance of Carbon Fiber Composites

Recycling Carbon Fiber from Carbon Fiber-Reinforced Polymer and Its Reuse in Photocatalysis: A Review

Carbon fibers recovery from CFRP recycling process and their usage: A review