Abstract:SUMMARY Objectives This study aimed to investigate bond performance of various resin luting cement (RLC) systems on enamel and dentin in different etching modes and to compare the RLC-tooth interface morphology using scanning electron microscopy (SEM). Methods and Materials The self-adhesive RLC systems used in combination with universal adhesives were as follows: Scotchbond Universal Adhesive Plus + RelyX Universal (3M Oral Care) and Clearfil Universal Bond Quick ER + SA Luting Multi (Kuraray Noritake Dental). These RLC systems were also used alone as self-adhesive RLC systems without universal adhesives (self-adhesive mode). The conventional RLC systems for comparison materials were as follows: BeautiBond Xtream + ResiCem EX (Shofu) and Tooth Primer + Panavia V5 (Kuraray Noritake Dental). Twelve specimens were prepared for each group to measure shear bond strength (SBS) in different etching modes. A stainless-steel rod was used as a substitute for indirect restorations. Bonded specimens were allocated to baseline (stored for 24 hours) and artificially aged (thermocycling [TC] for 10,000 cycles) groups. Representative treated tooth surfaces and RLC-tooth interfaces were observed using SEM. Results Three-way analysis of variance (ANOVA) revealed that all the factors (etching mode, storage period, and RLC system) had a significant influence on the enamel SBS values (p<0.05). Enamel SBS was significantly higher in etch-&-rinse (ER) mode than in self-etch (SE) mode, regardless of RLC system or storage period. Three-way ANOVA showed that all the factors had a significant influence on the dentin SBS values (p<0.001). Most RLC systems showed significantly higher dentin SBS in SE mode than in ER mode, regardless of storage period. However, the combination with Scotchbond Universal Adhesive Plus and RelyX Universal showed no significant difference in SBS values between etching modes at the baseline and showed a significantly higher SBS value in ER mode than in SE mode after TC. Conclusions The self-adhesive RLC systems with universal adhesives tended to show higher enamel and dentin bond performance than the self-adhesive RLC systems alone. The morphology of treated tooth surfaces and resin cement-tooth interfaces were dependent on the RLC system and etching mode used. The RLC systems with primer application showed a thin, high-density layer above the intact dentin in both etching modes, suggesting chemical interaction.

Micro-shear bond strength of resin composite cement to coronal enamel/dentin, cervical enamel, cementoenamel junction and root cementum with different adhesive systems

Influence of Casein Phosphopeptide-Amorphous Calcium Phosphate Application, Smear Layer Removal, and Storage Time on Resin-Dentin Bonding

Bond Strength Evaluation of a Self-Adhesive Composite Resin Cement in Vitro

[Evaluation of Shear Bond Strengths of Self-Etching and Total-Etching Dental Adhesives to Enamel and Dentin].

The Effect of Different Pre-Treatments on the Enamel Bonding Properties of a Self-Adhesive Resin Cement

Shear Bond Strength of Different Adhesive Systems to Silver Diamine Fluoride - Treated Carious Dentine

Bond Strength, Microleakage, Microgaps, and Marginal Adaptation of Self-adhesive Resin Composites to Tooth Substrates with and without Preconditioning with Universal Adhesives

The effects of the compatibility between resins and different adhesives on the shear bond strength and micro-leakage

Micro-shear Bond Strength of an Alternative Self-etch Application of “No Wait” Universal Adhesive to Caries-affected and Sound Dentin in Permanent and Primary Teeth

Influence of Peripheral Enamel Bonding and Chlorhexidine Pretreatment on Resin Bonding to Dentin.

[A Study on the Bonding Properties of Four Resin Cements].

An investigation of the shear bond strength of compomer restorative material to enamel and dentine

Comparing Various Resin Luting Cement Systems in Different Etching Modes Through Bond Durability and Morphological Features

Shear bond strength of universal adhesives to human enamel and dentin

Comparative evaluation of bonding performance between universal and self-etch adhesives: In vitro study

Cross-compatibility of methacrylate-based resin composites and etch-and-rinse one-bottle adhesives

Evaluation of shear bond strength of self-etching adhesive systems to enamel in different conditions

Micro-tensile bond testing of resin cements to dentin and an indirect resin composite

Evaluate the Shear Bond Strength of Self-Etching Bonding Systems Covered with Temporary Cements

Comparison of microtensile bonding strength of total-etch and self-etch adhesives

Micro-shear bond strength of a novel resin-modified glass ionomer luting cement (eRMGIC) functionalized with organophosphorus monomer to different dental substrates