Abstract:Sustainable development and green manufacturing are becoming an international consensus in the face of the threat of severe environmental pollution and waste of resources. Cryogenic air (CA) and nanofluid minimum quantity lubrication (NMQL) are state-of-the-art green manufacturing technologies. However, the lubricating performance of cryogenic air is ineffective, and the cooling ability of nanofluids minimum quantity lubrication is unsatisfactory. To specifically address the bottlenecks in these manufacturing methods, a new green processing technology combining their advantages was proposed, namely, cryogenic air nanofluid minimum quantity lubrication (CNMQL). Compared to traditional processing modes and other green technologies, cryogenic air nanofluid minimum quantity lubrication is superior for its economic efficiency, low carbon use, high utilization efficiency, energy saving as well as excellent cooling and lubricating performances. A surface grinding experiment was conducted under three lubricating conditions (cryogenic air, minimum quantity lubrication, and cryogenic air nanofluids minimum quantity lubrication) with Ti-6A1-4V as the workpiece material. Experimental results showed that: cryogenic air nanofluids minimum quantity lubrication achieved the best lubricating effect and obtained minimum specific grinding energy (51.96)/mm(3)) and friction coefficient (0.60), followed by nanofluids minimum quantity lubrication and cryogenic air. The lubricating mechanisms under cryogenic air nanofluids minimum quantity lubrication and nanofluids minimum quantity lubrication conditions were also analyzed according to the viscosity of nanofluid lubricants in grinding zone, contact angle, stability of lubricating oil film, atomization effect of droplets, and microtopography of workpiece surface. Relative to other conditions, the higher viscosity and larger contact angle of nanofluid lubricants under cryogenic air nanofluids minimum quantity lubrication condition led to higher stability and better lubricating effect of the lubricating oil film in the grinding zone. Droplets sprayed onto the grinding zone had a larger atomization angle, and the distribution density of droplets in the entire atomization spraying zone was relatively uniform. The droplets were uniformly distributed and had a larger spreading area, facilitating superior atomization effect in the grinding zone. On the other hand, workpiece surface had clear and smooth grinding pipelines, which presented minimal obstruction for the longitudinal flow and horizontal spreading effect of the micrometer pipelines, so the nanofluid lubricants achieved better spreading infiltration effect. Under the joint influence of the above factors, cryogenic air nanofluids minimum quantity lubrication achieved optimal lubricating effect, thus obtaining minimum specific grinding energy and friction coefficient. (C) 2018 Elsevier Ltd. All rights reserved.

Temperature of Grinding Carbide With Castor Oil-Based MoS2 Nanofluid Minimum Quantity Lubrication

Temperature of Grinding Carbide With Castor Oil-Based MoS<sub>2</sub> Nanofluid Minimum Quantity Lubrication

Specific Energy and G Ratio of Grinding Cemented Carbide under Different Cooling and Lubrication Conditions

Residual stress of grinding cemented carbide using MoS2 nano-lubricant

Grindability Evaluation of Ultrasonic Assisted Grinding of Silicon Nitride Ceramic Using Minimum Quantity Lubrication Based SiO2 Nanofluid

Experimental Study of Lubricating Property at Grinding Wheel/Workpiece Interface Under NMQL Grinding

Processing Characteristics of Vegetable Oil-based Nanofluid MQL for Grinding Different Workpiece Materials

Convective Heat Transfer Coefficient Model under Nanofluid Minimum Quantity Lubrication Coupled with Cryogenic Air Grinding Ti–6Al–4V

Grinding with minimum quantity lubrication: a comparative assessment

Tribological mechanism of carbon group nanofluids on grinding interface under minimum quantity lubrication based on molecular dynamic simulation

Performances of Al 2 O 3 /sic Hybrid Nanofluids in Minimum-Quantity Lubrication Grinding

Experimental Assessment of an Environmentally Friendly Grinding Process Using Nanofluid Minimum Quantity Lubrication with Cryogenic Air

Tribological Performance of Different Concentrations of Al2O3 Nanofluids on Minimum Quantity Lubrication Milling

Performance evaluation of nanofluid-based minimum quantity lubrication grinding of Ni-Cr alloy under the influence of CuO nanoparticles

Evaluation of minimum quantity lubrication grinding with nano-particles and recent related patents

Specific Energy and Surface Roughness of Minimum Quantity Lubrication Grinding Ni-based Alloy with Mixed Vegetable Oil-Based Nanofluids

Investigation on Surface Grinding of Ti-6Al-4V Using Minimum Quantity Lubrication

EHTT2022-Tribological Mechanism of Graphene/Ionic Liquid Nanofluid on Grain/Workpiece Grinding Interface under Nanofluid Minimum Quantity Lubrication

Modeling and Simulation of the Single Grain Grinding Process of theNano-Particle Jet Flow of Minimal Quantity Lubrication

Investigation of a green nanofluid added with graphene and Al 2 O 3 nano-additives for grinding hard-to-cut materials