Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Effect of Microsegregation on High‐Temperature Microstructure Evolution in Rapid Solidification Processed Nb‐Rich Ni Superalloys

Microstructure and Microsegregation in A Ni-Based Single Crystal Superalloy Directionally Solidified under High Thermal Gradient

Characterization of the Microstructure Evolution and Microsegregation in A Ni-Based Superalloy under Super-High Thermal Gradient Directional Solidification

EFFECT OF SOLIDIFYING RATE ON INTEGRALLY DIRECTIONALLY SOLIDIFIED MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY OF AN Nb-Ti-Si BASE ALLOY

Microstructural Evolution and Mechanical Properties of Rapidly Solidified Ni-Ge Alloys

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Microstructural Feature and Evolution of Rapidly Solidified Ni 3 Al-Based Superalloys

MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY EVOLUTION OF INTEGRALLY DIRECTIONALLY SOLIDIFIED Nb-SILICIDE-BASED ULTRAHIGH TEMPERATURE ALLOY

Solute Redistribution and Micromechanical Properties of Rapidly Solidified Multicomponent Ni-based Alloys

Microstructures and Nb-Rich Precipitation Behaviors of Inconel 718 Superalloy under Sub-rapid Solidification Process

Study on microsegregation and homogenization process of a novel nickel-based wrought superalloy

Microstructure and Element Segregation of Ni-Base Superalloy Casting with Radiation and Liquid-Metal Cooling

Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion

A new microsegregation model for rapid solidification multicomponent alloys and its application to single crystal nickel base superalloys of laser rapid directional solidification

Effect of Cooling Rate on Microsegregation During Solidification of Superalloy INCONEL 718 under Slow-Cooled Conditions

Microstructure, Segregation and Precipitate Evolution in Directionally Solidified GH4742 Superalloy

Facile Formation of a Superalloy-Like Microstructure in Ni77Ga23 Alloys by Rapid Solidification Processing

Effect of Cooling Rates on Solidification Microstructures and Tensile Property of a Novel Wrought Superalloy

Effect of Solidification Segregation on Microstructure and Mechanical Properties of a Ni-Cr-Mo-V Steel Weld Metal

Phase Field Simulation of Alloying Element Segregation During Solidification of DD5 Nickel-Base Single Crystal Superalloy

Effects of Solution Treatment Parameters on Microsegregation of a Ni-Based Single Crystal Superalloy