Abstract:Silicon -based ultra -thin flat heat pipes (UFHPs) that can be integrated with semiconductor devices provide an opportunity for electronic thermal management. To meet the requirements of various operation states, the impacts of gravity on the liquid plug characteristics and heat transfer performance of an UFHP are investigated by a visualization experiment conducted at different incline angles. Condensate flows back through microgrooves under the capillary pressure and gravity under a low heating power (capillary flow stage), and then excess condensate flows back along the edges of the UFHP under a higher heating power (gravitational flow stage). Over a certain heating power ( Q >= 14 W), liquid plug fluctuations caused by vapor entrainment are observed with periodic dry -out at the evaporator under large incline angles ( alpha >= 60 degrees ), corresponding to temperature fluctuations. Intense fluctuations of the liquid plug enhance sensible heat transfer, although the liquid plug occupies the condenser area and impedes the vapor flow. Meanwhile, evaporation at the evaporator benefits from corner -film evaporation until a large area of dry -out occurs. Due to the increased gravity and buoyancy, a larger incline angle is conducive to thermal performance enhancement, but this effect becomes restricted as the heating power rises. At a cooling -water temperature of 20 degrees C and an incline angle of 90 degrees , the lowest thermal resistances of the UFHP yield a value of 1.14 degrees C/W at 4 W in the steady stage and a value of 1.22 degrees C/W at 18 W in the fluctuation stage, respectively. The heat transfer limit of UFHP with overfilling reaches 24 W, compared with the theoretical heat transfer capacity of 8.9 W at an incline angle of 90 degrees . Additionally, a higher cooling -water temperature is beneficial for the thermal performance in the capillary flow stage, but not in the gravitational flow stage and fluctuation stage. This study provides guidance for the operational design of silicon -based UFHP for electronic thermal management.

Filling Ratio Optimization for High-Performance Nanoengineered Copper-Water Heat Pipes

High Performance Copper-Water Heat Pipes with Nanoengineered Evaporator Sections

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Transient Performance of a PCM-based Heat Sink with a Partially Filled Metal Foam: Effects of the Filling Height Ratio

Experimental Investigation of Thermal Performance of Miniature Heat Pipe Using SiO2-Water Nanofluids

Liquid Plug Characteristics and Heat Transfer Performance of a Silicon-Based Ultra-Thin Flat Heat Pipe at Different Incline Angles

Effects of filling ratio, geometry parameters and coolant temperature on the heat transfer performance of a wraparound heat pipe

EFFECTS OF CuO/WATER NANOFLUID APPLICATION ON THERMAL PERFORMANCE OF MESH WICK HEAT PIPE

Heat transfer performance on unequal-diameter pulsating heat pipe

EXPERIMENTAL STUDY ON IMPROVING HEAT TRANSFER ABILITY OF A HEAT PIPE UTILIZING IRON OXIDE-FERRIC OXIDE HYBRID AND NICKEL FERRITE MONO-MAGNETIC NANOFLUIDS

Heat Transfer Capacity Optimization Design of Microgroove and Microcolumn in an Ultra-Thin Flat Heat Pipe

Heat Transfer Characteristics of a New Type of Copper Wire-Bonded Flat Heat Pipe Using Nanofluids

An Experimental Investigation on Aqueous Fe–CuO Hybrid Nanofluid Usage in a Plain Heat Pipe

Experimental Investigation of Thermal Conduction Performance on Silicon-Based Micro Flat Heat Pipe

Effect of evaporation and condensation section length ratio on thermal performance of aluminum flat plate heat pipe with different micro grooved wicks

Design and performance evaluation of pulsating heat pipe using metallic nanoparticles based hybrid nanofluids

Heat Transfer and Nanofluids Flow Through the Circular Concentric Heat Pipes: a Comparative Study Using Least Square Method (LSM)

Experimental investigation of effects of extremely low pumping speed on isothermal performance and filling ratio of sintered copper heat pipe

Application of Nanofluid in an Inclined Mesh Wicked Heat Pipes

Combined effect of the magnetic field, orientation, and filling ratio on cylindrical pulsating heat pipe using distilled water and distilled water/Fe 3 O 4 nanofluid

Flexible heat pipes with integrated bioinspired design