Abstract:Abstract At present, there are many studies on the residual stress field and plastic strain field introduced by surface strengthening, which can well hinder the initiation of early fatigue cracks and delay the propagation of fatigue cracks. However, there are few studies on the effects of these key factors on fretting wear. In the paper, shot-peening (SP) and ultrasonic surface rolling process (USRP) were performed on Ti-6Al-4V plate specimens. The surface hardness and residual stresses of the material were tested by vickers indenter and X-ray diffraction residual stress analyzer. Microhardness were measured by HXD-1000MC/CD micro Vickers hardness tester. The effects of different surface strengthening on its fretting fatigue properties were verified by fretting fatigue experiments. The fretting fatigue fracture surface and wear morphology of the specimens were studied and analyzed by means of microscopic observation, and the mechanism of improving fretting fatigue life by surface strengthening process was further explained. After USRP treatment, the surface roughness of Ti-6Al-4V is significantly improved. In addition, the microhardness of the specimen after SP reaches the maximum at 80 μm from the surface, which is about 123% higher than that of the AsR specimen. After USRP, it reaches the maximum at 150 μm from the surface, which is about 128% higher than that of AsR specimen. It is also found that the residual compressive stress of the specimens treated by USRP and SP increases first and then decreases with the depth direction, and the residual stress reaches the maximum on the sub surface. The USRP specimen reaches the maximum value at 0.18 mm, about − 550 MPa, while the SP specimen reaches the maximum value at 0.1 mm, about − 380 MPa. The fretting fatigue life of Ti-6Al-4V effectively improved after USRP and SP. The surface integrity of specimens after USRP is the best, which has deeper residual compressive stress layer and more refined grain. In this paper, a fretting wear device is designed to carry out fretting fatigue experiments on specimens with different surface strengthening.

Improvement in Fatigue Performance of 2024-T3 Al Alloy Via Single Toroidal Roller Burnishing

Improvement of Fatigue Properties of EN AW 6082 Aluminum Alloy using Different Deep Rolling Directions

Multi-roller Taper Burnishing of Internal Chamfers and Its Enhancement Mechanism on 7050 Aluminum Alloy

Effect of surface integrity on fatigue life of 7075-T6 aluminum alloy by combination of fine turning with hydrostatic deep rolling

Effect of Roller Burnishing and Slide Roller Burnishing on Fatigue Strength of AISI 304 Steel: Comparative Analysis

Effect of ultrasonic surface rolling process on the fatigue performance of the 7075 aluminum alloy

On the influence of ultrasonic surface rolling process on surface integrity and fatigue performance of Ti-6Al-4V alloy

Enhanced fatigue performance of aluminum alloy through surface strengthening treatment

Surface Properties and Fatigue Behavior of 6061 Aluminum Alloy by Multi-pass Ultrasonic Surface Rolling Process

A study of shot peening and spinning rolling on fatigue of Al 7075 alloy samples

Research of the Ball Burnishing Impact over Cold-Rolled Sheets of AISI 304 Steel Fatigue Life Considering Their Anisotropy

Effect of Diamond Burnishing on Fatigue Behaviour of AISI 304 Chromium-Nickel Austenitic Stainless Steel

Improved fretting fatigue mechanism of surface-strengthened Ti-6Al-4V alloy induced by ultrasonic surface rolling process

Surface rolling deformed severity-dependent fatigue mechanism of Ti-6Al-4V alloy

Fatigue performance of medical Ti6Al4V alloy after mechanical surface treatments

Surface layer properties and fatigue behavior in Al 7075‐T73 and Ti‐6Al‐4V

Fatigue Behavior of Ultrafine-Grained 5052 Al Alloy Processed Through Different Rolling Methods

Significantly improvement in formability and ductility of AZ31 Mg alloy by differential temperature rolling

Influence of Grain Refinement and Microstructure on Fatigue Behavior for Solid-State Additively Manufactured Al-Zn-Mg-Cu Alloy

Influence of Ultrasonic Surface Rolling Process and Shot Peening on Fretting Fatigue Performance of Ti-6Al-4V

Deep Drawability of Al-Mg Alloys Produced by Twin Roll Continuous Casting Method: Investigation of Microstructure and Mechanical Properties