Abstract:The article presents the differences in some physical and chemical properties of wood with false heartwood, mature wood, and sapwood of Fagus sylvatica L: density of wood in the dry state, color in the color space CIE L*a*b* on the tangential surface and the planed surface at w = 10 ± 0.5%, as well as moisture and acidity of wet wood. As part of chemical analyses, the relative proportion of cellulose, hemicelluloses, lignin, and extractive substances in individual zones of beechwood in trunks with false heartwood was determined. From the carried out analyses, it follows that the biggest difference between the wood of false heartwood, mature wood, and sapwood is the color of the wood. The red-brown color of the wood with false heartwood in the color space CIE L*a*b* is described by the following coordinate values: L* = 64.9 ± 4.9; a* = 12.9 ± 1.4; b* = 19.6 ± 1.7. The most significant differences between the values of the color space are on the lightness coordinate, where the light ochre-white of mature wood shows a decrease of ∆L* = −14.0 compared with the color of false heartwood, and the white‒pale grey color of sapwood shows a decrease of ∆L* = −17.5. The density of dry beechwood with false heartwood is higher by ∆ρ0 = 4.7% than the density of mature wood, and the density of sapwood is ∆ρ0 = 12.3% lower than the density of wood with false heartwood. The exact opposite applies to the acidity of wet beechwood. The results of wet wood acidity measurements also point to certain differences. While the acidity of the wet wood of false heartwood is pH = 5.32 ± 0.13, the acidity of the sapwood is 5.1% lower. The higher acidity of beech heartwood is attributed to the presence of organic acids in polyphenols during heartwood formation. From the comparison of the representation of cellulose, hemicellulose, lignin, and extractive substances, it follows that the relative content of lignin and hemicelluloses is higher in false heartwood than in mature wood and sapwood. On the contrary, the content of holocellulose and cellulose is highest in sapwood. The presented divisions in the physical and chemical properties of beechwood with false heartwood do not limit the use of beechwood in industrial applications, except for a change in color; the definition of color boundaries in the color space CIE L*a*b* creates space for sorting beechwood according to color and can be used to increase the color variety of compositions of construction-carpentry products.

Specific heat capacity of wood between −140 and 50 °C in dry and wet state

Thermophysical Properties of Beech Wood in the Range from Room Temperature to 900 °C

Theoretical and Experimental Study on Transient Measurement of Wood Thermal Properties

Thermal properties of wood: measurements by transient plane source method in dry and wet conditions

MOISTURE SORPTION ISOTHERMS AND ISOSTERIC HEATS OF SORPTION OF HIGH-PRESSURE TREATED PAULOWNIA WOOD UNDER DIFFERENT STORAGE CONDITIONS

Impregnation of wood with a paraffinic phase change material for increasing heat capacity

Experimental Measurements of Thermal Conductivity of Wood Species in China: Effects of Density, Temperature, and Moisture Content

Physical, mechanical, and thermal properties of heat-treated poplar and beech wood

Experimental Study of the Anisotropic Thermal Conductivity of Spruce Wood

Mass loss kinetics of thermally modified wood species as a time–temperature function

Viscoelastic properties of wood across the grain measured under water-saturated conditions up to 135\degree C: evidence of thermal degradation

Measurements of specific heat capacity of common building materials at elevated temperatures: a comparison of DSC and HDA

Swelling kinetics of thermally modified wood

The compressive behaviour of beech and birch at different moisture and temperature conditions along the grain

Differences in Some Physical and Chemical Properties of Beechwood with False Heartwood, Mature Wood and Sapwood

Viscoelastic properties of green wood across the grain measured by harmonic tests in the range of 0\degree C to 95\degree C. Hardwood vs. softwood and normal wood vs. reaction wood

The Influence of Wood Moisture Content on the Processes of Freezing and Heating

The vibrational properties of native and thermally modified wood in dependence on its moisture content

Exploratory study on the bending performance of thermo-hydro-mechanically densified Scots pine (Pinus sylvestris L.) at elevated temperatures

Characterisation of thermally treated beech and birch by means of quasi-static tests and ultrasonic waves

Effect of High-Temperature Paraffin Impregnation on the Properties of the Amorphous Cellulose Region Based on Molecular Dynamics Simulation