Abstract:The original version of this Article omitted the following from the Acknowledgements:‘J.D. and H. Zhang acknowledge initial funding for design of the meta-atoms provided by the National Science Foundation under award CMMI-1266251. Z.L. and H. Zheng contributed to the Device Fabrication section and were independently funded as visiting scholars by the National Natural Science Foundation of China under award 51772042 and the “111” project (No. B13042) led by Professor Huaiwu Zhang. Later work contained within the Device Modeling and Device Characterization sections and some revisions to the manuscript were funded under Defense Advanced Research Projects Agency Defense Sciences Office (DSO) Program: EXTREME Optics and Imaging (EXTREME) under Agreement No. HR00111720029. The authors also acknowledge fabrication facility support by the Harvard University Center for Nanoscale Systems funded by the National Science Foundation under award 0335765. The views, opinions and/or findings expressed are those of the authors and should not be interpreted as representing the official views or policies of the Department of Defense or the U.S. Government.’ This has been corrected in both the PDF and HTML versions of the Article.

Corrigendum to “Determination of Hardness and Fracture Toughness of Y-TZP Manufactured by Digital Light Processing through the Indentation Technique”

Erratum to: Description of full-range strain hardening behavior of steels

Corrigendum to: Mechanical properties and wear-corrosion resistance of a new compound extrusion process for magnesium alloy AZ61

Corrigendum to "Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures" [Heliyon 10(2) January 2024 e24428]

Correction to "Fracture Conductivity Prediction Based on Machine Learning"

Corrections to “zinc Oxide Nanostructures and High Electron Mobility Nanocomposite Thin Film Transistors” [nov 08 3001-3011

Correction To: Network-Strengthened Ti-6Al-4V/(TiC+TiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures

Correction to "Proppant Settlement and Long-Term Conductivity Calculation in Complex Fractures"

Erratum: Corrigendum: Printing, folding and assembly methods for forming 3D mesostructures in advanced materials

Correction: Tang, L. et al., Effect of Oxygen Variation on High Cycle Fatigue Behavior of Ti-6Al-4V Titanium Alloy. Materials 2020, 13, 3858

Erratum to “Femtosecond Laser Direct Ablating Micro/Nanostructures and Micropatterns on CH3NH3PbI3 Single Crystal”

Author Correction: Microscopic and mechanical properties of undisturbed and remoulded red clay from Guiyang, China

Author Correction: Additive Manufacturing of Ultrafine-Grained High-Strength Titanium Alloys

Erratum: Ultrathin conformal devices for precise and continuous thermal characterization of human skin

Corrigendum to “Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process” [Mater. Sci. Eng. A 662 (2016) 456–467] (S0921509316303148) (10.1016/j.msea.2016.03.097))

Correction: Effect of the content and strength of hard segment on the viscoelasticity of the polyurethane elastomer: insights from molecular dynamics simulation

Author Correction: Ultra-thin high-efficiency mid-infraredtransmissive Huygens meta-optics

Correction To: Effect of Y2O3 Addition on the Microstructure, Wear Resistance, and Corrosion Behavior of W-4.9Ni-2.1Fe Heavy Alloy

Correction: Tong et al. Effect of Micro-Textures on the Surface Interaction of WC+Co Alloy Composite Coatings. Coatings 2022, 12, 1242

Corrigendum: The Development of a Magnesium-Releasing and Long-Term Mechanically Stable Calcium Phosphate Bone Cement Possessing Osteogenic and Immunomodulation Effects for Promoting Bone Fracture Regeneration

Corrigendum to “development of Methods for Detecting the Fate of Mesenchymal Stem Cells Regulated by Bone Bioactive Materials” [bioact. Mater. 6(3) (2021) 613–626]