Abstract:Unlike the dual-layer membranes in which dual-layers attached tightly after co-casting, the attainment of independent poly (vinylidene fluoride) (PVDF) membranes with uniformly rough surface structures necessitates the delamination of top-layer membranes from the underlying PVDF membranes. The coverage of top-layer membranes via co-casting is expected to reduce the solvent/nonsolvent exchange rate for the underlying PVDF membranes during a phase inversion process. In this context, a polyethersulfone (PES) membrane was cocast onto a PVDF membrane followed by phase inversion in a water bath to fabricate PVDF membranes for membrane distillation (MD). The spontaneous delamination of PES from PVDF membranes occurs once the membrane solidifies. Due to the combined effect of the additional PES layer and the solvent retained at the PES/ PVDF interface, delayed liquid-liquid (L-L) demixing and crystallization of the PVDF solution take place during the phase separation process, resulting in the formation of a porous surface with symmetric cross-section. Results show that the PVDF concentration significantly affects the membrane morphology. Increasing the PVDF content from 16 wt% to 20 wt% leads to a marked morphological change for membrane cross-section from cellular pores to PVDF particles, which indicates that the phase inversion mechanism varies from delayed L-L demixing to solidliquid (S-L) demixing; this is mainly affected by the solution viscosity. Due to the roughness increment by the particulate surfaces, the hydrophobicity of co-cast PVDF membranes (PVDF-co) is distinctly enhanced compared to the single-layer PVDF membranes. Furthermore, the pore sizes of the PVDF-co membranes are enlarged, and the thicknesses are reduced. Therefore, the PVDF-co membranes have much higher fluxes than the single-layer PVDF membranes, especially for PVDF-co-20 membranes composed of large PVDF particles which show superior pore interconnectivity than the cellular pores. A long-term stability test is conducted with the PVDF-20-21 membrane for 48 h using a 3.5 wt% NaCl solution at the feed and permeate temperatures of 60 C and 20 C, respectively. Fairly steady fluxes are observed over the testing course, as well as a continuous high salt rejection of above 99.95%

Surface Segregation and Self‐Assembly of Block‐Copolymer Separation Layers on Top of Homopolymer Substructures in Asymmetric Ultrafiltration Membranes from a Single Casting Step

Fundamental and application of amphiphilic copolymers in high performance MF/UF membranes

Ionic Liquid Mediated One-step Perpendicular Assembly in Block Copolymer Thin Films for Ultrafiltration Membrane Applications

Homoporous Polymer Membrane Via Forced Surface Segregation: A Computer Simulation Study

Tailoring Membrane Surface Properties and Ultrafiltration Performances via the Self-Assembly of Polyethylene Glycol-block-Polysulfone-block-Polyethylene Glycol Block Copolymer upon Thermal and Solvent Annealing.

A Co-Casting Route Enables the Formation of Skinless, Hydrophobic Poly (vinylidene Fluoride) Membranes for DCMD

One-Step Water-Induced Phase Separation Simultaneously Triggering Polymer Solidification and Polyelectrolyte Complexation for Porous Ultrafiltration Membranes

Dual-Phase Separation in a Semiconfined System: Monodispersed Heterogeneous Block-Copolymer Membranes for Cell Encoding and Patterning.

Preparation Of Isoporous Membranes From Low Chi Block Copolymers Via Co-Assembly With H-Bond Interacting Homopolymers

Electrostatic enhanced surface segregation approach to self-cleaning and antifouling membranes for efficient molecular separation

Microstructure Manipulation in PVDF/styrene-maleic Anhydride Copolymer Composite Membranes: Effects of Miscibility on the Phase Separation

Quaternization and Degradation of Block Copolymer Templates for UF and ED Membranes Via Non-Solvent Induced and Solvent Evaporation Induced Phase Separation

Enhanced membrane antifouling and separation performance by manipulating phase separation and surface segregation behaviors through incorporating versatile modifier

Achieving Persistent High-Flux Membranes Via Kinetic and Thermodynamic Synergistic Manipulation of Surface Segregation Process

Toward Predicting the Formation of Integral‐Asymmetric, Isoporous Diblock Copolymer Membranes

Surface Segregation‐Induced Superwetting Separation Membranes with Hierarchical Surface Structures and Internalized Gel Networks

Antifouling Asymmetric Block Copolymer Nanofilms via Freestanding Interfacial Polymerization for Efficient and Sustainable Water Purification

Surface-induced Self-Assembly of Amphiphilic Block Copolymers into Functional Bilayer Thin Films.

Strain-Induced Nanocavitation in Block Copolymer Thin Films for High Performance Filtration Membranes

Blending Polyvinylidene Difluoride with Copolymers of Carboxymethyl Betaine and Methyl Methacrylate to Develop Low-Fouling Microfiltration Membranes Via Non-Solvent Induced Phase Separation

Surface Microphase Separation in PDMS‐b‐PMMA‐b‐PHFBMA Triblock Copolymer Films