Abstract:Abstract High molecular weight polystyrene homopolymers with low dispersity were synthesized by a reversible addition-fragmentation chain transfer (RAFT) polymerization method using 0.03 and 0.3 wt% of cumyl dithiobenzoate (CDB) vs. styrene (St) and the azobis(isobutyronitrile) initiator, at the polymerization temperature of 60 or 70 °C. The optimal high molecular weight polystyrene via this synthetic scheme shows M w = 46.5×104, M n = 33.3×104, and a dispersity of 1.40. The polystyrene chain contains a dithiobenzoate C=S moiety and thus can be used as a macro-chain-transfer agent for the polymerization of other monomers and for the synthesis of diversified block copolymers under mild conditions. The changes of the polystyrene molecular weight and dispersity were studied by the influences of the initial concentration ratio of CDB to styrene ([CDB]0/[St]0), the polymerization temperature, and the polymerization time. The PS molecular weight is inversely proportional to the [CDB]0/[St]0 ratio. Decreasing CDB from 0.3 to 0.03 wt%, a high MW PS was obtained, while the dispersity was observed to increase from 1.10 to 1.40. The PS molecular weight increases with the increase of the reaction time, while the dispersity of PS varies little from 1.12 to 1.23. The molecular weight and dispersity increase with the increase of the polymerization temperature. As the temperature arises from 60°C to 70°C, the conversion increases considerably from 25.8% to 39.9%, and the dispersity increases slightly from 1.15 to 1.17. As the temperature reaches 80°C, the conversion increases considerably to 64.7%, and the dispersity increases to 1.53. The polymer molecular weight of the polystyrene prepared by the RAFT method is suitable for the applications of engineering materials.

Molecular weight standards from sulfonation of polystyrene

DETERMINATION AND APPLICATION OF MARK-HOUWINK CONSTANTS OF SYNDIOTACTIC POLYSTYRENE

Preparation of Cellulose Sulphate with High Substitution Using Concentrated Sulfuric Acid and Propanol

Experimental investigation on the reliability of routine SEC–MALLS for the determination of absolute molecular weights in the oligomeric range

Synthesis of Isotactic Polystyrene in Hydrocarbons by Initiation with T-Buli in the Presence of Sodium Dodecylbenzenesulfonate

PREPARATION AND CHARACTERIZATION OF SULFONATED POLYSTYRENE LATEXES

Characterizing Styrene Monomer and Oligomers by SEC/MALS/VISC/DRI

Synthesis and physical properties of sulfonated syndiotactic polystyrene ionomers

Synthesis in pilot plant scale and physical properties of sulfonated polystyrene

Preparation of highly sulfonated polystyrene model colloids

New Evaluation Methods of Average Molecular Weight and the Degree of Branching of Poly(1,4-phenylene sulfide) Samples through Their Partial Sulfonation

Number Concentration Measurements of Polystyrene Submicrometer Particles

Ir Study on Monomolecular Particle Agglomerates of Polystyrene Obtained by Freeze-Drying of Its Dilute Solution

Preparation and Application of Sulfonated Poly(1-Octene-Co-Styrene)

Analysis of Ft-Ir Spectra of the Sulfonated Polystyrene Colloidal Crystals

Preparation of Monodisperse and Anion‐Charged Polystyrene Microspheres Stabilized with Polymerizable Sodium Styrene Sulfonate by Dispersion Polymerization

Sulfonated polystyrene and its characterization as a material of electrolyte polymer

Synthesis and characterization of high molecular weight and low dispersity polystyrene homopolymers by RAFT polymerization

Synthesis and Characterization of Cross-linked Sulfonated Polystyrene Nanoparticles

COMPARISON OF DSC TRACES OF POLYSTYRENES SYNTHESIZED BY ANIONIC POLYMERIZATION

Preparation of Polystyrene/Sio2 Composite Nanoparticles Bearing Sulfonic Groups on the Surface Via Emulsion Copolymerization Using A Polymerizable Emulsifier