Abstract:In order to realize the utilization of coal-fired solid waste and captured carbon dioxide, the effects of ratio of solid waste, mineralized curing pressure and mineralized curing temperature on the compressive strength and carbon fixation rate of aerated concrete were studied, with the coal-based waste, coal ash and desulfurization gypsum as the main raw materials and slag as the supplementary cementitious material. The crystal phase structure and micro morphology under different mineralized curing conditions were analyzed by XRD and SEM, and the effect of different mineralized curing conditions on the pore structure of aerated concrete was studied by MIP. The experimental results show that the appropriate residual water/slag ratio is helpful to improve the CO 2 fixation rate and early compressive strength of aerated concrete. When the CO 2 curing pressure increases from 0.05 MPa to 1.00 MPa, the carbon fixation rate increases by 24.8%, and the compressive strength increases first and then decreases. When the curing pressure is 0.1 MPa, the maximum compressive strength is reached. With the CO 2 curing temperature rising from 25 ℃ to 105 ℃, the carbon fixation rate and compressive strength increases first and then decreases. The carbon fixation rate reaches maximum of 7.21% at 45 ℃, and the compressive strength reaches maximum of 3.53 MPa at 65 ℃. According to analysis of XRD and SEM, the major mineralized products are CaCO 3 , which mainly exist in the form of calcite and vaterite. Higher curing pressure（≥0.2 MPa） is likely to cause micro-cracks at the product interface. With the increase of curing temperature, the mineralized products and hydrated products appear simultaneously. According to MIP analysis, the influence of mineralized curing on the pores of aerated concrete can be divided into two aspects: on the one hand, CaCO 3 and other products with small particle size can fill the pores of 10-50 nm, on the other hand, reaction heat of mineralization and volumetric expansion of products can cause the increase of 30-60 μm pores. The microstructure can be optimized by increasing the curing temperature, which can make the distribution of pores more uniform.

Effect of MnO2 and Li2CO3 on Compressive Strength and Thermal Conductivity of Aerated Concrete

Carbonation Curing of Industrial Solid Waste‐based Aerated Concretes

Accelerated Carbonation of Biochar Reinforced Cement-Fly Ash Composites: Enhancing and Sequestering CO2 in Building Materials

Effect of Nano CaCO3 on the Properties of Autoclaved Aerated Concrete

Effects of Curing Regimes on Calcium Oxide–Belite–Calcium Sulfoaluminate-Based Aerated Concrete

Study on formulation of aerated concrete by CO2 mineralization using coal ash

Effective thermal conductivity of moist aerated concrete with different porosities

Study on the preparation and performances analysis of lightweight high strength ceramsite aerated concrete

Effect of Nanostructured Additive Based on Graphene Oxide and Lignosulfonate on Water Absorption and Thermal Conductivity of Non-Autoclavated Aerated Concrete

Combined effect of silica fume and fly ash as cementitious material on strength characteristics, embodied carbon, and cost of autoclave aerated concrete

Innovative use of solid CO2 as an eco-friendly additive in alkali-activated concrete for enhancing its performance

Effect of Graphite on the Self-Sensing Properties of Cement and Alkali-Activated Fly Ash/slag Based Composite Cementitious Materials

Effect of Ordinary Portland Cement and Water Glass on the Properties of Alkali Activated Fly Ash Concrete

Carbon dioxide as an admixture for better performance of OPC-based concrete

Regulating Effect of Cement Accelerator on High Content Solid-Wastes Autoclaved Aerated Concrete (HCS-AAC) Slurry Performance and Subsequent Influence

Effect of Pore Structure on Thermal Conductivity and Mechanical Properties of Autoclaved Aerated Concrete

Effects of foam stabilizers on the properties and microstructure of autoclaved aerated concrete from iron tailings

Synergizing Portland Cement, high-volume fly ash and calcined calcium carbonate in producing self-compacting concrete: A comprehensive investigation of rheological, mechanical, and microstructural properties

Effect of Foaming Agent, Binder and Density on the Compressive Strength and Thermal Conductivity of Ultra-Light Foam Concrete

Utilization of Carbide Slag in Autoclaved Aerated Concrete Preparation

Influencing factors of mechanical and thermal conductivity of foamed phosphogypsum-based composite cementitious materials