Abstract:The recently developed tough and self-healing hydrogels, containing a large number of physical bonds, have found widespread applications in bioengineering and soft electronics. Owing to the sophisticated physical interactions and organization, these hydrogels often demonstrate structural heterogeneities, which strongly influence their mechanical performances. Using poly(N,N-dimethyl acrylamide-co-methacrylic acid) hydrogels (P(DMAA-co-MAAc)) with dynamic hydrogen bonds (H-bonds) as a model system, the structural characterization has been carried out in this study using small-angle X-ray scattering (SAXS) and small-angle neutron scattering (SANS) analyses, along with exploring the influence of the structure on the mechanical properties. By systematically tuning the polymer composition, including the monomer fraction and chemical cross-linking density, two different hydrogel regions with distinct mechanical properties were observed: the swollen regions and shrunk regions. The former was mechanically weak, whereas the latter exhibited a tough behavior. Both types of hydrogels were noted to be highly heterogeneous, which results from the nanoscale spatial polymer concentration fluctuations at ∼100 nm scale. Combined with the contrast variation utilizing SANS, the structure parameters, including the polymer volume fraction of the dense and sparse regions, volume fraction occupied in the space, and average correlation length of the long-range and short-range heterogeneous structures, were explored using a scaling model based on a two-phase system composed of the densely and sparsely cross-linked regions. Using in situ SAXS, the microscopic deformation of the tough and shrunk hydrogels was noted to follow the affine deformation, while a significantly non-affine deformation was observed in the swollen hydrogels, which might have led to the different mechanical performances of these materials.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acs.macromol.1c01064.Swelling volume ratio of hydrogels 0.14-0.2% during the drying–swelling cycle (Figure S1); FT-IR spectra of PDMAA, PMAAc, and P(DMAA-co-MAAc) and temperature dependence of FT-IR spectrum of P(DMAA-co-MAAc) (Figure S2); semi-empirical quantum chemical calculations for revealing the conformation features and their interaction in water (Figure S3); tensile stress–strain curves of P(DMAA-co-MAAc) hydrogels f-0.1% with various f values (0.12, 0.13, and 0.15) and P(DMAA-co-MAAc) hydrogels 0.14-x with various x values (0.05, 0.1, and 0.15%) (Figure S4); 1D scattering intensity as a function of the scattering vector q under various stretch ratios for the hydrogels f-0.1% with the molar fraction of DMAA varying from 0.12 to 0.15 and hydrogels 0.14-x with the chemical cross-linking density ranging from 0.05 to 0.15% (Figures S5 and S6); stretch-induced structure evolution of the swollen hydrogel 0.14-0 (Figure S7); tensile stress–strain curve of hydrogel 0.14-1% and the corresponding Mooney–Rivlin plot (Figure S8); and structural parameters of the swollen and shrunk hydrogels (Table S1) (PDF)This article has not yet been cited by other publications.

Preparation of poly(acrylamide‐co‐2‐acrylamido‐2‐methylpropan sulfonic acid)‐g‐Carboxymethyl cellulose/Titanium dioxide hydrogels and modeling of their swelling capacity and mechanic strength behaviors by response surface method technique

Tough Supramolecular Hydrogels with Excellent Self-Recovery Behavior Mediated by Metal-Coordination Interaction

Structure Optimization and Mechanical Model for Microgel-Reinforced Hydrogels with High Strength and Toughness

Multi-physically Cross-Linked Hydrogels Simultaneously with MPa Level Mechanical Strengths and High Equilibrium Water Content above 70 %

Modeling and Simulation of Swelling Behavior of Thermosensitive Hydrogels

Optimization of Key Parameters Affecting Swelling Capacity of Poly(acrylamide-co-acrylic acid) Hydrogels in Salt Water Using Response Surface Methodology (RSM)

Hydrophobically Associated Poly(acrylamide/octadecyl acrylate)-Carboxymethyl Cellulose Hydrogels: Synthesis, Characterization, and Shape Memory Ability

Optimizing the composition of gelatin methacryloyl and hyaluronic acid methacryloyl hydrogels to maximize mechanical and transport properties using response surface methodology

Carboxymethyl cellulose-chitosan composite hydrogel: Modelling and experimental study of the effect of composition on microstructure and swelling response

Preparation and Properties of Polyacrylamide/ Titanium Oxide Hydrogels

Mechanical characterization and modeling of sponge-reinforced hydrogel composites under compression.

Response Surface Method Based Modeling and Optimization of CMC-g Terpolymer Interpenetrating Network/Bentonite Superabsorbent Composite for Enhancing Water Retention

Swelling and Viscoelastic Properties of Cellulose-Based Hydrogels Prepared by Free Radical Polymerization of Dimethylaminoethyl Methacrylate in Cellulose Solution

Tough Hydrogels with Dynamic H-Bonds: Structural Heterogeneities and Mechanical Performances

Superabsorbent polyacrylamide grafted carboxymethyl cellulose pH sensitive hydrogel: I. Preparation and characterization

Design of a Rubbery Carboxymethyl Cellulose/Polyacrylic Acid Hydrogel Via Visible-Light-Triggered Polymerization

Mechanically Robust Polyacrylamide Composite Hydrogel Achieved by Integrating Lamellar Montmorillonite and Chitosan Microcrystalline Structure into Covalently Cross-linked Network

Design artificial intelligence-based optimization and swelling behavior of novel crosslinked polymeric network hydrogels based on acrylamide-2-hydroxyethyl methacrylate and acrylamide-N-isopropylacrylamide

Tailoring Hydrogel Sheet Properties through Co-Monomer Selection in AMPS Copolymer Macromers

Plastic-Like Supramolecular Hydrogels with Polyelectrolyte/Surfactant Complexes as Physical Cross-links

Tuning morphology and mechanical property of polyacrylamide/Laponite/titania dual nanocomposite hydrogels by titania