Abstract:Abstract Helical flow of non-Newtonian fluids in concentric and eccentric annuli is of great interest in oil/gas well drilling. Experimental results and field measurements demonstrated that frictional pressure loss in the annulus can be affected substantially by the rotation of the drillpipe. Previous studies indicated that the influence of pipe rotation on annular friction pressure loss is affected by fluid properties, flow regime, annular diameter ratio and eccentricity. This article presents results of in-depth experimental and theoretical investigations conducted on the flow of yield power law (Herschel Buckley) fluids in concentric and eccentric annuli with pipe rotation. The aim of this study is to develop a reliable hydraulic model that accounts for the effect of pipe rotation in annular pressure loss calculations. Extensive flow experiments with polymer-based fluids were carried out using a newly developed testing facility. Four different annular geometries have been considered for the investigation. Five different formulations of test fluid were prepared by varying concentrations of Xanthan Gum (XG) and Polyanionic Cellulose (PAC) for each annular geometry. Accurate fluid characterization was made using the horizontal pipe sections and a rotational viscometer. In addition to the experimental work, theoretical analysis of helical flows in concentric annuli was carried out. Experimental results indicate the strong presence of shear thinning and inertial effects when inner pipe rotates. In highly eccentric annuli, inertial effects dominate the phenomenon of shear thinning and result in increased pressure loss as the speed increases. Inertial effects can be generated due eccentricity and/or geometric irregularities of the annulus that substantially influence the velocity field as the pipe rotates. The experimental measurements and theoretical analysis presented in this investigation are very useful for hydraulic program optimization and well control, particularly for managed pressure drilling (MPD) operations. Introduction Helical flow of non-Newtonian fluids in concentric and eccentric annuli is of great interest in oil well drilling. Laboratory test results 1–7 and field measurements 8–16 demonstrated that frictional pressure loss in the annulus can be affected substantially by the rotation of the drill pipe. The effect of pipe rotation on friction pressure loss is mainly influenced by fluid properties (rheology and density), flow regime, diameter ratio and eccentricity. The change in friction pressure loss due pipe rotation is attributed to different flow phenomena such as:shear thinning in non-Newtonian fluid;inertial effects resulting from pipe eccentricity and/or geometric irregularities such as drillpipe wobbling or eccentricity variation and;formation of secondary flows. Shear Thinning: Shear thinning in non-Newtonian flows tends to reduce the friction pressure loss due to the coupling of axial and rotational flow through shear rate dependent apparent viscosity function. Inertial Effect: Streamlines in concentric annular flow form perfectly helical pattern. This means that the magnitude of velocity of a fluid element at a given radius from the center is constant. However, a rotating eccentric pipe and/or wobbling drillpipe generates very complicated flow patterns in the annulus, resulting in substantial variation of the velocity of a fluid element along the streamline. Consequently, the inertial effects that positively influence the friction pressure loss counteract the effect of shear thinning in eccentric annuli.

Influence of Vertical Downward Annulus Eccentricity on Steam-Water Two-Phase Flow Pressure Drop

Modeling fluctuating pressure in the eccentric annulus with a four-parameter rheological method

Steam Conformance along Horizontal Well with Different Well Configurations of Single Tubing: an Experimental and Numerical Investigation

Modeling of yield-power-law fluid flow in an eccentric annulus with fixed horizontal cuttings bed

Mathematical Modeling of Heat Transfer and Pressure Drops in the Single- and Dual-Pipe Horizontal Wells

Experimental Study and Modeling of Yield Power-Law Fluid Flow in Annuli with Drillpipe Rotation

Study on the pressure wave velocity model of multiphase fluid in the annulus of dual-gradient drilling

Experimental investigation on the water hammer characteristic of stalling fluid in eccentric casing-tubing annulus

Enhanced Annular Pressure Drop Modeling Assists to Drill Extreme Shallow Ultra-ERD Wells

Experimental Investigation on Air-Water Two-Phase Flow Pattern and Pressure Drop in Vertical Upward Annulus

Pressure Drop Predicting Model for Gas and Oil-Based Drilling Fluid Two Phase Flow in Vertical Annulus

Improving displacement efficiency by optimizing pad fluid injection sequence during primary cementing of eccentric annulus in shale gas horizontal wells

Study on Non-Isothermal Three-Phase Flow Characteristics in Large-Diameter Drilling Annular

A Numerical Simulation Approach for Superheated Steam Flow during Multipoint Steam Injection in Horizontal Well

Experimental Investigation of Pressure Drop Oscillations of Steam Water Two Phase Flow in Helically Coiled Tubing Boiler Reactors

Effect of Yield Power Law Fluid Rheological Properties on Cuttings Transport in Eccentric Horizontal Narrow Annulus

Influence of Casing Eccentricity on the Mechanical Integrity of Cement Sheaths in Fractured Wells

PREDICTION OF VOID FRACTION AND PRESSURE DROP FOR UPWARD GAS-LIQUID TWO-PHASE FLOW THROUGH VERTICAL CONCENTRIC ANNULUS

Numerical Characterization of the Annular Flow Behavior and Pressure Loss in Deepwater Drilling Riser

CFD Method for Predicting Annular Pressure Losses and Cuttings Concentration in Eccentric Horizontal Wells

FRICTIONAL PRESSURE DROP CHARACTERISTICS OF STEAM-WATER TWO-PHASE FLOW IN HELICALLY COILED TUBES ORIENTED WITH VARIOUS AXIAL ANGLES