Abstract:Purpose: Computational fluid dynamics (CFD) and 4D-flow magnetic resonance imaging (MRI) are synergically used for the simulation and the analysis of the flow in a patient-specific geometry of a healthy thoracic aorta. Methods: CFD simulations are carried out through the open-source code SimVascular. The MRI data are used, first, to provide patient-specific boundary conditions. In particular, the experimentally acquired flow rate waveform is imposed at the inlet, while at the outlets the RCR parameters of the Windkessel model are tuned in order to match the experimentally measured fractions of flow rate exiting each domain outlet during an entire cardiac cycle. Then, the MRI data are used to validate the results of the hemodynamic simulations. As expected, with a rigid-wall model the computed flow rate waveforms at the outlets do not show the time lag respect to the inlet waveform conversely found in MRI data. We therefore evaluate the effect of wall compliance by using a linear elastic model with homogeneous and isotropic properties and changing the value of the Young's modulus. A stochastic analysis based on the polynomial chaos approach is adopted, which allows continuous response surfaces to be obtained in the parameter space starting from a few deterministic simulations. Results: The flow rate waveform can be accurately reproduced by the compliant simulations in the ascending aorta; on the other hand, in the aortic arch and in the descending aorta, the experimental time delay can be matched with low values of the Young's modulus, close to the average value estimated from experiments. However, by decreasing the Young's modulus the underestimation of the peak flow rate becomes more significant. As for the velocity maps, we found a generally good qualitative agreement of simulations with MRI data. The main difference is that the simulations overestimate the extent of reverse flow regions or predict reverse flow when it is absent in the experimental data. Finally, a significant sensitivity to wall compliance of instantaneous shear stresses during large part of the cardiac cycle period is observed; the variability of the time-averaged wall shear stresses remains however very low. Conclusions: In summary, a successful integration of hemodynamic simulations and of MRI data for a patient-specific simulation has been shown. The wall compliance seems to have a significant impact on the numerical predictions; a larger wall elasticity generally improves the agreement with experimental data.

Quantitative Hemodynamics in Aortic Dissection: Comparing in Vitro MRI with FSI Simulation in a Compliant Model

4D Flow MRI-Based Computational Analysis of Blood Flow in Patient-Specific Aortic Dissection.

Hemodynamic Effects of Entry and Exit Tear Size in Aortic Dissection Evaluated with In Vitro Magnetic Resonance Imaging and Fluid-Structure Interaction Simulation

The Potential of Computational Fluid Dynamics Simulation on Serial Monitoring of Hemodynamic Change in Type B Aortic Dissection

Numerical simulation of two-phase non-Newtonian blood flow with fluid-structure interaction in aortic dissection

Validation of the Reduced Unified Continuum Formulation Against In Vitro 4D-Flow MRI

Abstract 589: A Fluid Structure Interaction Workflow For Studying Aortic Dissections

A proposal of risk indicators for pathological development from hemodynamic simulation: application to aortic dissection

Assessment of aortic dissection remodeling with patient-specific fluid-structure interaction models

Numerical simulation of hemodynamics in aortic dissection

Computational modeling of the fluid flow in type B aortic dissection using a modified finite element embedded formulation

Aortic Dissection Blood Two-Phase Flow Numerical Simulation Study

Validation of Numerical Simulations of Thoracic Aorta Hemodynamics: Comparison with In Vivo Measurements and Stochastic Sensitivity Analysis

Hemodynamics in a three-dimensional printed aortic model: a comparison of four-dimensional phase-contrast magnetic resonance and image-based computational fluid dynamics

A new method for scaling inlet flow waveform in hemodynamic analysis of aortic dissection

Aortic dissection simulation models for clinical support: fluid-structure interaction vs. rigid wall models

Patient-specific compliant simulation framework informed by 4DMRI-extracted Pulse Wave Velocity: Application post-TEVAR

Investigating the role of thrombosis and false lumen orbital orientation in the hemodynamics of Type B aortic dissection

Patient Specific Hemodynamics: Combined 4d Flow-Sensitive Mri And Cfd

Hemodynamic Evaluation of Type B Aortic Dissection Using Compressed Sensing Accelerated 4D Flow MRI

Computational Fluid Dynamics Investigation of Chronic Aortic Dissection Hemodynamics Versus Normal Aorta