Abstract:This study aims to examine the impact of agricultural waste materials—specifically silicon carbide (SiC) and palm sprout shell ash (PSSA)—on the mechanical properties, including density, porosity, tensile strength, compression strength, flexural strength, impact strength, and hardness, as well as the tribological behavior of Al-Cu-Mg alloy-based HRAMMCs. Parametric optimization was conducted on HRAMMCs to predict the effect of input constraints on the performance of the composite, considering the weight percentage of SiC, PSSA, and ultrasonic-assisted stirring time. Taguchi's L9 orthogonal array was used for the design of experiments (DOE), and the composites were fabricated accordingly. Their physical, mechanical, and tribological properties were determined experimentally. Taguchi-based Grey Relational Analysis for multi-optimization highlighted the potential of the HRAMMCs, with a density of 2.545 g/cm3, porosity of 5.810%, ultimate tensile strength of 341 MPa, flexural strength of 321 MPa, compressive strength of 394.016 MPa, Vickers hardness of 136.883 HV, wear rate of 6.88E-12 m3/m, and a coefficient of friction of 0.397. ANOVA shows that the developed mathematical model is a better fit for examining the impact of various factors on the GRG of and corresponding properties of developed HRAMMCs, Indicating the R2 value of the developed model is 99.33% (0.9933). The 2 wt.% SiC, 2 wt.% PSSA, and a stirring time of 7 minutes are optimal parameters for the present HRAMMCS; to reduce porosity, wear loss, and the coefficient of friction while increasing flexural strength, ultimate tensile strength, compressive strength, and Vickers microhardness. Moreover, the examination of the tensile and impact fracture surfaces and worn surfaces was carried out using SEM analysis of the alloy and composite produced under the optimal experimental conditions. The results of the fracture surface analysis indicated that the failure of both tensile and impact fractures was due to a amalgamation of ductile and brittle behaviors. The composites exhibited lower ductility than that of the base alloys. A study of the wear mechanism revealed that it was a mixture of adhesive and abrasive wear mechanisms. The SiC and PSSA ceramic reinforcements demonstrate higher hardness compared to the alloy, which restricts the fluid-like movement of the matrix. When these reinforcements were added to the alloy, they substantially decreased the occurrence of severe delamination and the formation of adhesive wear particles.

Process Optimization and Studies on Mechanical Characteristics of AA2014/Al2O3 Nanocomposites Fabricated Through Ultrasonication Assisted Stir–Squeeze Casting

Optimization of Squeeze Casting Process Parameters on AA8011 Based Hmmcs Under NaCl Environment

Optimization of process parameters in fabricating AA6082 /Nip surface composite using friction stir processing technique

Optimization of process variables and characterization of mechanically agitated ceramic‐microsphere reinforced aluminium composite

Experimental analysis and optimization of process parameters using response surface methodology of surface nanocomposites fabricated by friction stir processing

Optimization studies of stir casting parameters and mechanical properties of TiO2 reinforced Al 7075 composite using response surface methodology

Synthesis of Stir-Cast AA7050/5%B4C Composite and Optimization of EDM Response Parameters Using Taguchi Analysis

Taguchi-based Grey Relational Analysis for multi-response optimization of the characteristics of HRAMMCs reinforced with agro-waste and SIC produced by ultrasonic-assisted bottom pour two-stage stir casting

Nanoarchitectonics of AA7075-NbC Surface Composites for Augmenting the Mechanical and Tribological Properties

Optimization of process parameters of aluminum alloy AA 2014-T6 friction stir welds by response surface methodology

Synthesis of AA8050/B4C/TiB2 Hybrid Nanocomposites and Evaluation of Computer-Aided Machining Parameters

Multiresponse optimization of fabrication variables of α-MnO2-epoxy nanocomposite through simulation-based Taguchi-grey relational analysis

Effect of Nanoaluminium Nitride Ceramic Particles on Microstructure, Mechanical Wear, and Machining Behavior of Al-Si-Mg Alloy Matrix Composites Produced by Bottom Pouring Type Stir Casting Route

Optimization of process parameters of boron carbide filled Aluminium matrix composites using Grey Taguchi method

Mechanical and Sliding Wear Performance of AA356-Al2O3/SiC/Graphite Alloy Composite Materials: Parametric and Ranking Optimization Using Taguchi DOE and Hybrid AHP-GRA Method

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Microstructural evolution and property evaluation of in‐situ Al‐MgAl2O4 nanocomposite prepared by ɣ‐Al2O3 and ultrasonication‐assisted impeller mixing

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

Development of high-performance aluminium 6061/SiC nanocomposites by ultrasonic aided rheo-squeeze casting method

Optimization of CNC-WEDM Parameters for AA2024/ZrB2 in situ Stir Cast Composites Using Response Surface Methodology with Desirability Function Technique

ASSESSMENT OF MACHINABILITY BEHAVIOUR OF LM24 – NANO Al2O3 – Gr HYBRID COMPOSITES THROUGH STIR CASTING TECHNIQUE