Abstract:Additive technologies enable the flexible production through scalable layer-by-layer fabrication of simple to intricate geometries. The existing 3D-printing technologies that use powders are often slow with controlling parameters that are difficult to optimize, restricted product sizes, and are relatively expensive (in terms of feedstock and processing). This paper presents the development of an alternative approach consisting of a CAD/CAM + combined wire arc additive-manufacturing (WAAM) hybrid process utilizing the robotic MIG-based weld surfacing and milling of the AlSi5 aluminum alloy, which achieves sustainably high productivity via structural alloys. The feasibility of this hybrid approach was analyzed on a representative turbine blade piece. SprutCAM suite was utilized to identify the hybrid-manufacturing parameters and virtually simulate the processes. This research provides comprehensive experimental data on the optimization of cold metal transfer (CMT)–WAAM parameters such as the welding speed, current/voltage, wire feed rate, wall thickness, torch inclination angle (shift/tilt comparison), and deposit height. The multi-axes tool orientation and robotic milling strategies, i.e., (a) the side surface from rotational one-way bottom-up and (b) the top surface in a rectangular orientation, were tested in virtual CAM environments and then adopted during the prototype fabrication to minimize the total fabrication time. The effect of several machining parameters and robotic stiffness (during WAAM + milling) were also investigated. The mean deviation for the test piece's tolerance between the virtual processing and experimental fabrication was −0.76 mm (approx.) at a standard deviation of 0.22 mm assessed by 3D scanning. The surface roughness definition Sa in the final WAAM pass corresponds to 36 μm, which was lowered to 14.3 μm after milling, thus demonstrating a 55% improvement through the robotic comminution. The tensile testing at 0° and 90° orientations reported fracture strengths of 159 and 161.3 MPa, respectively, while the yield stress and reduced longitudinal (0°) elongations implied marginally better toughness along the WAAM deposition axes. The process sustainability factors of hybrid production were compared with Selective Laser Melting (SLM) in terms of the part size freedom, processing costs, and fabrication time with respect to tight design tolerances. The results deduced that this alternative hybrid-processing approach enables an economically viable, resource/energy feasible, and time-efficient method for the production of complex parts in contrast to the conventional additive technologies, i.e., SLM.

Advanced metal transfer additive manufacturing of high temperature turbine blades

Additive Manufacture of Prototype Turbine Blades for Hot-Fired Engine Performance Validation Trials

Ceramic and Metal Additive Manufacturing of Monolithic Rotors From Sialon and Inconel and Comparison of Aerodynamic Performance for 300W Scale Microturbines

Progress on additive manufacturing of 600 ℃ high-temperature titanium alloys

Advanced 3D additive manufacturing techniques for revolutionizing the next-generation rocket engine nozzle fabrication

Application of additive technologies for manufacturing turbine stator parts in aircraft engines

Sustainable Hybrid Manufacturing of AlSi5 Alloy Turbine Blade Prototype by Robotic Direct Energy Layered Deposition and Subsequent Milling: An Alternative to Selective Laser Melting?

Additive Manufacturing of IN100 Superalloy Through Scanning Laser Epitaxy for Turbine Engine Hot-Section Component Repair: Process Development, Modeling, Microstructural Characterization, and Process Control

A Review on the Processing of Aero-Turbine Blade Using 3D Print Techniques

3D plasma metal deposition for processing multi material Titanium parts

Alloy 718: Laser Powder Bed Additive Manufacturing for Turbine Applications

A novel magnetic field assisted powder arc additive manufacturing for Ti60 titanium alloy: Method, microstructure and mechanical properties

Development of metal AM technology for gas turbine components

Development of a method for manufacturing ceramic tooling for precision casting of blades made of heat-resistant alloys using additive technologies

Innovations in Casting Techniques for Single Crystal Turbine Blades of Superalloys

Hybrid Fabrication of Cold Metal Transfer Additive Manufacturing and Laser Metal Deposition for Ti6Al4V: The Microstructure and Dynamic/Static Mechanical Properties

Integrated Computational Design of Three-Phase Mo–Si–B Alloy Turbine Blade for High-Temperature Aerospace Applications

Additive Manufacturing of Nickel-Based Super Alloys for Aero Engine Applications

Powder-Binder Jetting Large-Scale, Metal Direct-Drive Generators: Selecting the Powder, Binder, and Process Parameters

A Review of Additive Manufacturing Techniques and Post-Processing for High-Temperature Titanium Alloys

Fabrication of TiAl alloys turbocharger turbine wheel for engines by metal injection molding