Abstract:The milling of polymer composites is a process that ensures dimensional and shape accuracy and appropriate surface quality. The shaping of thin-walled elements is a challenge owing to their deformation. This article presents the results of milling polymer composites made of glass and carbon fibers saturated with epoxy resin. The milling of each material was conducted using different tools (tools with polycrystalline diamond inserts, physically coated carbide inserts with titanium nitride and uncoated carbide inserts) to show differences in feed force and deformation after the machining of individual thin-walled samples. In addition, the study used recurrence analysis to determine the most appropriate quantifications sensitive to changes occurring in milling different materials with the use of different tools. The study showed that the highest forces occurred in milling thin-walled carbon-fiber-reinforced plastics using uncoated tools and the highest feeds per revolution and cutting speeds. The use of a high feed per revolution (0.8 mm/rev) in carbon-fiber-reinforced plastics machining by uncoated tools resulted in a maximum feed force of 1185 N. A cutting speed of 400 m/min resulted in a force of 754 N. The largest permanent deformation occurred in the milling of glass-fiber-reinforced composite samples with uncoated tools. The permanent deformation value of this material was 0.88 mm. Low feed per revolution (0.1 mm/rev) resulted in permanent deformations of less than 0.30 mm for both types of materials. A change in feed per revolution had the most significant effect on the deformations of thin-walled polymer composites. The analysis of forces and deformation made it possible to conclude that high feed per revolution were not recommended in composite milling. In addition to the analysis of machining thin-walled composites, the novelty of this study was also the use of recurrence methods. Recurrence methods were used to determine the most appropriate quantifications. Determinism, averaged diagonal length and entropy have been shown to be suitable quantifications for determining the type of machined material and the tools used.

Surface texture of the milled surface of aluminum-ceramic composite

A Study on 3D Micro-Topographical Measurement of FRCMC Grinding Surface

Some observations in grinding surface quality of FRCMC

A Study on Grinding Surface Waviness of Woven Ceramic Matrix Composites

Multi-sensor measurements of titanium alloy surface texture formed at subsequent operations of precision machining process

Characterization and Defect Analysis of Machined Regions in Al-SiC Metal Matrix Composites Using an Abrasive Water Jet Machining Process

Comparison of tool life and surface characteristics of uncoated, coated carbide and ceramic tools during machining of SiC reinforced ZA43 alloy MMC

Analysis of the influence of cutting parameters on surface roughness and cutting forces in high speed face milling of Al/SiC MMC

The Influence of Selected Laser Engraving Parameters on Surface Conditions of Hybrid Metal Matrix Composites

Characterization and optimization analysis on surface finish and energy consumption in turning of Al-4032/GMP MMC produced by stir casting

Evaluation of tool wear when machining SiCp-reinforced Al-2014 alloy matrix composites

Assessment of machined surface for SiC f /SiC ceramic matrix composite during ultrasonic vibration-assisted milling-grinding

3D surface topography analysis and functionality-related performance of the machined surface in slot micro-milling titanium alloy Ti6Al4V

Effect of surface roughness and study of cutting force in milling of Al/Sic metal matrix composites

On understanding the specific cutting mechanisms governing the workpiece surface integrity in metal matrix composites machining

Simulation and experimental investigation on the cutting mechanism and surface generation in machining SiCp/Al MMCs

Experimental Analysis of Ductile Cutting Regime in Face Milling of Sintered Silicon Carbide

Study on the milling surface quality of 20% volume fraction SiCp/Al composites

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Towards the understanding the effect of surface integrity on the fatigue performance of silicon carbide particle reinforced aluminium matrix composites

Machinability Measurements in Milling and Recurrence Analysis of Thin-Walled Elements Made of Polymer Composites