Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Experimental investigation of multi-wall carbon nanotube added epoxy resin on the EDM performance of epoxy/carbon fiber/MWCNT hybrid composites

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Effects Of Corona Discharge On The Surface Structure, Morphology And Properties Of Multi-Walled Carbon Nanotubes

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Effects of CNT Microstructural Characteristics on the Interfacial Enhancement Mechanism of Carbon Fiber Reinforced Epoxy Composites Via Molecular Dynamics Simulations

Micro-end-milling of carbon nanotube reinforced epoxy nanocomposites manufactured using three roll mill technique

Characterization of the interface and interphase region in the multi-walled carbon nanotube modified epoxy resin/carbon fiber hybrid nanocomposite

Surface Morphology Analysis of Inconel 625 through Multi-walled Carbon Nanotubes-Based Electric Discharge Machining

Enhanced thermomechanical properties of epoxy-multiwalled CNT nano-composites

Machinability investigation and surface modification of nano-TiB2 and AlN grafted MWCNT hybridized Al 7075 matrix ternary composite through powder-mixed EDM

Experimental Study on the Comparison between Network Microstructure Titanium Matrix Composites and Ti6Al4V on EDM Milling

Effects of carbon nanotubes on open-hole carbon fiber reinforced polymer composites

Hole Quality and Damage in Drilling Carbon/Epoxy Composites by Electrical Discharge Machining

Modelling and Optimization of Machining of SiC-CNT Conductive Ceramic Composite used for Micro and Nano Sensor by Electrical Discharge Machining

Investigation of delamination and surface quality of machined holes in drilling of multiwalled carbon nanotube doped epoxy/carbon fiber reinforced polymer nanocomposite

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

Effect of MWCNTs on Wear Behavior of Epoxy Resin for Aircraft Applications

The Feasibility Analysis of Electrical-Discharge Machining of Carbon-Carbon Composites

Effect of multi-walled carbon nanotubes on the performance evaluation of nickel-based super-alloy–Udimet 720 machined using WEDM process

Simultaneous Ultrasonication‐assisted Internal Mixing to Prepare MWCNTs‐filled Epoxy Composites with Increased Strength and Thermal Conductivity

The effect of carbon nanotubes loading and processing parameters on the electrical, mechanical, and viscoelastic properties of epoxy-based composites