Abstract:Additive manufacturing and annealing process of short carbon fiber‐reinforced nylon 6. The mechanical properties of short carbon fiber‐reinforced nylon 6 (CF‐PA6) components formed by fused filament fabrication (FFF) are significantly affected by the process parameters of additive manufacturing and heat treatment. In this study, the effects of printing speed, carbon fiber aspect ratio, and annealing temperature on fiber orientation were investigated by observation of single‐layer‐single‐fiber samples. Furthermore, a two‐stage annealing process was proposed to increase the tensile modulus of CF‐PA6 based on the correlation analysis results between the degree of fiber alignment and the variation of tensile modulus. According to the calculation of the Pearson correlation coefficient, the tensile modulus was highly correlated with the degree of fiber alignment under different printing speeds and fiber aspect ratios. The variation in tensile modulus and fiber orientation was also consistent when the annealing temperature was lower than the crystallization temperature. Conversely, the variation of tensile modulus and fiber orientation were opposite, as the annealing temperature was higher than the crystallization temperature because of the influence of crystallinity. Through increasing the degree of fiber alignment and crystallinity of the parts, the proposed two‐stage annealing method could increase the tensile modulus of the parts to 9.0 GPa, which was 16.81% higher than that of single‐temperature annealing. Highlights The effects of annealing temperature, carbon fiber aspect ratio and printing speed on fiber orientation were illustrated. The relationship between the degree of fiber alignment and the variation of tensile modulus was established. The proposed two‐stage annealing method, considering fiber orientation and crystallinity, significantly increased the tensile modulus of CF270‐PA6 parts from 7.7 to 9.0 GPa. The quantitative analysis of the fiber orientation is realized by the statistical analysis of the plane fiber orientation angle of the single‐layer‐single‐fiber sample.

Effect of fiber content and fiber orientation on mechanical behavior of fused filament fabricated continuous-glass-fiber-reinforced nylon

Anisotropic mechanical properties of oriented carbon fiber filled polymer composites produced with fused filament fabrication

Assessment of the effects of the addition of continuous fiber filaments in PA 6/short fiber 3D-printed components using interrupted in-situ x-ray CT tensile testing

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Dimensional Accuracy and Mechanical Properties of Chopped Carbon Reinforced Polymers Produced by Material Extrusion Additive Manufacturing

Additive manufacturing of short carbon filled fiber nylon: effect of build orientation on surface roughness and viscoelastic behavior

Effect of fiber orientation on the failure behavior of a glass-fiber reinforced thermoplastic composite

Effect on mechanical properties of CFRP composites in different fiber orientations

Effect of nanofiller alignment on the mode-I cohesive parameters of CNF-doped GFRP composites

Additive manufacturing of continuous fibre reinforced thermoplastic composites using fused deposition modelling: Effect of process parameters on mechanical properties

Two‐stage annealing method for short carbon fiber‐reinforced nylon 6 in fused filament fabrication

Experimental Characterization and Analysis of the In-Plane Elastic Properties and Interlaminar Fracture Toughness of a 3D-Printed Continuous Carbon Fiber-Reinforced Composite

Optimization of Production Parameters for Impact Strength of 3D-Printed Carbon/Glass Fiber-Reinforced Nylon Composite in Critical ZX Printing Orientation

Fiber Orientation and Strain Rate-Dependent Tensile and Compressive Behavior of Injection Molded Polyamide-6 Reinforced with 20% Short Carbon Fiber

Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fiber Fabrication Technology

Strain rate dependence of 3D printed continuous fiber reinforced composites

The Effect of Chopped Carbon Fibers on the Mechanical Properties and Fracture Toughness of 3D-Printed PLA Parts: An Experimental and Simulation Study

Mechanical Properties and Economic Analysis of Fused Filament Fabrication Continuous Carbon Fiber Reinforced Composites

Influence of Interfacial Interaction and Composition on Fracture Toughness and Impact Properties of Carbon Fiber-Reinforced Polyethersulfone

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Process-structure-property analysis of short carbon fiber reinforced polymer composite via fused filament fabrication