Abstract:Uniaxial and cruciform biaxial tensile tests are performed on a face-centered cubic material AA6016-T4 and a body-centered cubic material DP490 under 19 different loading paths, i.e., uniaxial tension in seven directions and biaxial tension in rolling/transverse and 45°/135° directions, with seven and four stress ratios, respectively. The ability of several yield criteria to describe the plastic anisotropy for the tested materials, under the associated and non-associated flow rules is evaluated systematically. A new evaluation strategy to check the validity and applicability of the material models is proposed in this paper. This strategy is different from the traditional evaluation method in that the biaxial tensile mechanical properties measured in the 45°/135° sampling direction are included in the investigation scope, and it is not limited to the rolling/transverse sampling direction, i.e., the yield stress functions are evaluated by comparing the experimental and predicted uniaxial yield stresses, plastic work contours on the normal and diagonal planes. Further, the plastic potential functions are confirmed by the description accuracy of uniaxial rα-values and the directions of plastic strain rate in the rolling/transverse and 45°/135° directions. A new analytical calibration program is developed for the material parameters of the Poly6 yield criterion related to normal (a1,a2,...,a7) and shear stress components (a8,a9,...,a16), which can further introduce the yield stresses under the near plane strain states (σPS0, σPS45, and σPS90) and pure shear yield stress along the RD (τ0). The results indicate that the new calibration strategy of Analytical Poly6-II&2 can accurately describe the anisotropic yield behavior of the tested materials compared with other advanced yield criteria, especially for plastic work contours on the diagonal plane. Significant anisotropic yield behavior was observed under biaxial tensile stress states with the same loading ratio in different sampling directions, therefore, investigating the prediction accuracy of the biaxial tensile mechanical properties in only the rolling/transverse sampling direction is insufficient for evaluating the effectiveness of the material models; the mechanical properties at the initial yield point cannot fully reflect the plastic anisotropy of the materials. The material parameters of the Analytical Poly6-II&2 yield criterion are expressed as functions of equivalent plastic strain, which can continuously capture the evolution of the anisotropic yield behavior for AA6016-T4 and DP490. Three different calibration strategies of material parameter a16 do not affect the description ability of uniaxial tensile yield stresses, rα-values, and plastic work contours on the normal plane, but will change the calculation results of plastic work contours on the diagonal plane. When both τ0 and σPS45 are available, a more balanced prediction accuracy can be obtained.

Prediction of yield surfaces of textured sheet metals

A multi-scale modelling framework for anisotropy prediction in aluminium alloy sheet and its application in the optimisation of the deep-drawing process

A new anisotropic-asymmetric yield criterion covering wider stress states in sheet metal forming

Modeling stress anisotropy, strength differential, and anisotropic hardening by coupling quadratic and stress-invariant-based yield functions under non-associated flow rule

Predicting the in-plane mechanical anisotropy of 7085 aluminum alloys through crystal plasticity simulations and machine learning

Characterization and modelling of evolving plasticity behaviour up to fracture for FCC and BCC metals

An Experimental Methodology to Characterize the Plasticity of Sheet Metals from Uniaxial to Plane Strain Tension

Effect of Different Yield Criteria and Material Parameter Identification Methods on the Description Accuracy of the Anisotropic Behavior of 5182-O Aluminum Alloy

A general yield function with differential and anisotropic hardening for strength modelling under various stress states with non-associated flow rule

Investigation of Yield Surfaces Evolution for Polycrystalline Aluminum after Pre-Cyclic Loading by Experiment and Crystal Plasticity Simulation

Establishing the relationship between generalized crystallographic texture and macroscopic yield surfaces using partial input convex neural networks

Modeling of Eyld2000-2d Anisotropic Yield Criterion Considering Strength Differential Effect and Analysis of Optimal Calibration Strategy

Crystal Plasticity Simulation of Yield Loci Evolution of SUS304 Foil

Strength modeling of sheet metals from shear to plane strain tension

Evolution of yield behavior for AA6016-T4 and DP490 - Towards a systematic evaluation strategy for material models

Anomalous texture developments, new two-dimensional primary growth modeling, and fully ( 001 ) -textured electrical steels

Investigation of evolving yield surfaces of dual-phase steels

Lode-dependent Yld91 function for anisotropic-asymmetric hardening modeling of metals under non-associated flow rule

Earing Prediction of AA5754-H111 (Al-Alloy) with Linear Transformation-Based Anisotropic Drucker Yield Function under Non-Associated Flow Rule (Non-AFR)

Material modeling of 6016-O and 6016-T4 aluminum alloy sheets and application to hole expansion forming simulation

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing