Abstract:<p>It is usually deformed severely for thin-walled workpiece when the fixture is removed after machining, which is mainly caused by the redistribution of internal stress and machining induced residual stress (MIRS). Previous works have tried to relax the fixture in-processes to release the residual stresses (i.e. internal stress and MIRS), and perform the following machining operation after re-fasten the workpiece at its totally relaxed state. However, the totally relaxed state is only an equilibrium of residual stresses and the MIRS on the top layer of the workpiece will be changed after the following machining process. The residual stresses of the workpiece become imbalance again and thus will lead to the deformation of final component. In this paper, a novel research work of actively controlling the in-processes deformation of thin-walled part is presented, which is aimed at balancing the internal stress/MIRS and preventing the redistribution of residual stresses after last machining step. Firstly, the variations of internal stress, MIRS and clamping force during machining are analyzed through a simplified in-process model of blade. An equilibrium equation is established by taking the residual stresses as the equivalent loads of clamping point. Next, to achieve the proposed in-processes active control method, a mathematical model of how to actively adjust the fixture between machining operations is established. And then, the finite element method (FEM) is used to calculate the MIRS induced deformation, in which the MIRS is measured through experiment. A prototype of active control fixture for blade part is developed to adjust the in-process deformation. Finally, three groups of machining experiments on a simplified blade with three different treatments on the fixture after the rough machining – no relaxing the fixture at all, totally relaxing the fixture in-process, and actively controlling the deformation in-process– are carried out. The validation demonstrates that the proposed in-process active control method could decrease machining deformation significantly. The maximum deformation reduced to 18.3 % and 42.9 % compare to the no relaxing and totally relaxing the fixture after rough milling.</p>

The influence of ice-based fixture on suppressing machining-induced deformation of cantilever thin-walled parts: a novel and green fixture

Investigation of Moving Fixture on Deformation Suppression During Milling Process of Thin-Walled Structures

Finite Element Simulation for Optimal Clamping Scheme of Thin-Walled Workpiece in Milling Process

Research on precision machining for ultra-thin structures based on 3D in-situ ice clamping

Force-Induced Deformation Mechanism for Cylindrical Shell Thin-Walled Parts Milling With Ice Supporting: Modeling and Prediction

Finite Element Simulation and Analysis of Deformation in Machining of Aeronautical Aluminum Alloy Thin-Walled Workpiece

Numerical Simulation and Analysis of Symmetry and Step-symmetry Milling of Aerospace Thin-walled Workpiece

Study on milling flatness control method for TC4 titanium alloy thin-walled parts under ice fixation

Machining fixture and deformation control of aero-engine thin-walled casing

602 FEM-based Simulation for Workpiece Deformation in Thin-Wall Milling

An adaptive clamp system for deformation control of aerospace thin-walled parts

Milling performance of cryogenic cooled titanium alloy thin-walled parts based on cantilever sheet

A new in-processes active control method for reducing the residual stresses induced deformation of thin-walled parts

Optimization Method of Floating Fixture Layout for Distortion Control of Low-Stiffness Thin-Walled Beams

Machining deformation of single-sided component based on finishing allowance optimization

Finite Element Simulation and Deformation Control of High-Speed Milling of Al7050-T7451 Thin-walled Parts

A Rapid Design Method of Anti deformation Fixture Layout for Thin Walled Structures

An Adaptive Fixture for Suppress Vibrations and Measuring Workpiece Deformation of Thin-Walled Casings

Elastic Mechanics-Based Fixturing Scheme Optimization of Variable Stiffness Structure Workpieces for Surface Quality Improvement

A machining deformation control method of thin-walled part based on enhancing the equivalent bending stiffness

Application of low-melting alloy in the fixture for machining aeronautical thin-walled component