Abstract:One of the most important tasks when drilling a borehole is to select the appropriate type of drilling fluid and adjust its properties to the borehole’s conditions. This ensures the safe and effective exploitation of the borehole. Many types of drilling fluids are used to drill holes for crude oil and natural gas. Most often, mainly due to cost and environmental constraints, water-based muds are used. On the other hand, invert drilling fluids are used for drilling holes in difficult geological conditions. The ratio of the oil phase to the water phase in invert drilling fluids the most common ratio being from 70/30 to 90/10. One of the disadvantages of invert drilling fluids is their cost (due to the oil content) and environmental problems related to waste and the management of oily cuttings. This article presents tests of invert drilling fluids with Oil-Water Ratio (OWR) 50/50 to 20/80 which can be used for drilling HPHT wells. The invert drilling fluids properties were examined and their resistance to temperature and pressure was assessed. Their effect on the permeability of reservoir rocks was also determined. The developed invert drilling fluids are characterized by high electrical stability ES above 300 V, and stable rheological parameters and low filtration. Due to the reduced content of the oil, the developed drilling fluid system is more economical and has limited toxicity.
What problem does this paper attempt to address?
The main problem that this paper attempts to solve is to develop a reverse drilling fluid with a high internal - phase content (i.e., water - phase content) in order to reduce the oil - phase content in traditional reverse drilling fluids, thereby reducing drilling costs and environmental impacts. Specifically, the authors studied the properties of reverse drilling fluids with an oil - to - water ratio (OWR) ranging from 50/50 to 20/80, and evaluated the stability, rheology, and filtration loss of these drilling fluids under high - temperature and high - pressure conditions, as well as their impact on the permeability of reservoir rocks.
### Main research contents:
1. **Preparation of reverse drilling fluids**:
- Reverse drilling fluids with different oil - to - water ratios were prepared using materials such as mineral oil, emulsifiers (ENI and ENII), 35% calcium chloride solution, and organic clay.
- The oil - to - water ratios were 50/50, 40/60, 35/65, 30/70, 25/75, and 20/80 respectively.
2. **Performance tests**:
- **Density**: Measured using a Baroid - type liquid balance.
- **Rheological parameters**: Measured using an Ofite 900 viscometer and an Ofite 77 high - temperature and high - pressure viscometer.
- **Filtration loss**: Measured using a low - pressure filtration loss tester and a static high - temperature and high - pressure filtration loss tester.
- **Electrical stability**: Measured using an electrical stability tester.
- **Stability**: The TSI value was measured using a Turbiscan Tower device.
- **Impact on the permeability of reservoir rocks**: The impact of the drilling fluid on the permeability of sandstone cores was determined through experiments.
### Main findings:
- **Electrical stability**: The electrical stability ES values of the prepared drilling fluids were between 610 and 690 volts, indicating that these drilling fluids had good electrical stability.
- **Rheological and structural parameters**: As the water - phase content increased, the plastic viscosity and yield point of the drilling fluid gradually increased. For example, for the drilling fluid with an oil - to - water ratio of 20/80, its plastic viscosity reached 85 mPa·s, and its yield point reached 30.1 Pa.
- **Density**: Increasing the water - phase content can increase the density of the drilling fluid, up to 1.23 g/cm³ without the need to add weighting materials.
- **Temperature impact**: In the temperature range from 20 to 120°C, the plastic viscosity and yield point of the drilling fluid changed with temperature. For example, for the drilling fluid with an oil - to - water ratio of 40/60, the plastic viscosity decreased to 29 mPa·s at 120°C, and the yield point remained at about 13.4 Pa.
- **Permeability impact**: The experimental results showed that drilling fluids with different oil - to - water ratios had different impacts on the permeability of reservoir rocks, but overall, these drilling fluids caused less damage to the reservoir.
### Conclusion:
By adjusting the types and amounts of emulsifiers, reverse drilling fluids with an oil - to - water ratio as low as 20/80 can be successfully prepared. These drilling fluids have good rheological and stability properties, can work effectively under high - temperature and high - pressure conditions, and have a relatively small impact on the permeability of reservoir rocks. This new type of drilling fluid is expected to play an important role in reducing costs and environmental impacts.