Studying the effect of heat treatment modes on corrosion resistance of welded joints
Nataliya Kalinina,Vasiliy Kalinin,Ivannа Serzhenko
DOI: https://doi.org/10.30977/bul.2219-5548.2021.94.0.23
2021-12-16
Bulletin of Kharkov National Automobile and Highway University
Abstract:Welded joints with corrosion-resistant steels and heat-resistant alloys, which require different modes of heat treatment to achieve the level of mechanical properties specified in the design documentation, are used for the manufacture of parts and components of the turbo-pumping unit (TPU) and liquid rocket engine. Heat-resistant alloys are a large group of alloys on iron, nickel and cobalt bases with the addition of chromium and other alloying elements (C, V, Mo, Nb, W, Ti, Al, B, etc.), whose main feature is to maintain high strength at high and cryogenic temperatures. Heat-resistant alloys are used in the manufacture of many parts of gas turbines in rocketry and jet aircraft, stationary gas turbines, the pumping of oil and gas, hydrogenation of fuel in metallurgical furnaces and many other installations. For the doping of nickel chromium γ-solid solution, several elements are used, which differently influence the increase of heat resistance and processability. Along with the main reinforcing elements (Ti, Al), refractory elements (W, Mo, Nb) are introduced into the alloy, which increase the thermal stability of the solid solution. Heat resistant alloys are based on cobalt. Cobalt has a positive effect on the heat-resistant properties of alloys. The introduction of chromium in cobalt increases its heat resistance and hardness. In addition to chromium, alloys containing cobalt include additives of other alloying elements that improve their various properties at high temperatures. A characteristic feature of these alloys is that they have relatively low heat resistance characteristics at moderate temperatures, which, however, change a little with the temperature up to 900 ° C and therefore become quite high compared to the characteristics of other heat-resistant alloys. A significant drawback of these alloys is their high cost due to the costly cobalt. Nickel-based heat-resistant alloys typically have a complex chemical composition. It includes 12–13 components, carefully balanced to obtain the required properties. The content of impurities such as silicon (Si), phosphorus (P), sulfur (S), oxygen (O) and nitrogen (N) is also controlled. The content of elements such as selenium (Se), tellurium (Te), lead (Pb) and bismuth (Bi) should be negligible, which is provided by the selection of charge materials with low content of these elements, because it is not possible to get rid of them during melting. These alloys typically contain 10–12 % chromium (Cr), up to 8% aluminum (Al) and titanium (Ti), 5–10 % cobalt (Co), as well as small amounts of boron (B), zirconium (Zr) and carbon (C). Molybdenum (Mo), tungsten (W), niobium (Nb), tantalum (Ta) and hafnium (Hf) are sometimes added. Heat-resistant alloys are used for the production of many parts of gas turbines in rocketry and jet aircrafts, stationary gas turbines, for pumping oil and gas products, for hydrogenation of fuel in metallurgical furnaces and in many other installations. Nickel-based heat-resistant alloys are also cryogenic, i.e., they are capable of operating and retaining mechanical properties at very low temperatures (–100 °C to –269 °C). Such alloys are chromium-nickel alloys having an austenitic structure. Not only do they have good mechanical properties that do not change over a large temperature range (–200 °C to 900 °C), they can also work in corrosive environments. Nickel-based heat-resistant alloys typically have a complex chemical composition. It includes 12–13 components, carefully balanced to obtain the required properties. Welded and combined workpieces are made of separate components that are interconnected by various welding methods. Welded and combined blanks greatly simplify the creation of complex configuration designs. Improper workpiece design or incorrect welding technology can cause defects (grooves, porosity, internal stresses) that are difficult to correct by machining. Given that finding replacements with multiple materials, working them out in production, and investigating interconnectivity during thermal forces in a product can take considerable time and money, it would be best to replace one alloy. Unifying the material used would allow the structure to work as a whole, which would increase the manufacturability of the products. After examining the different replacement options, inconel 718 was selected for the study. Studies of welded specimens of inconel 718 alloy-stainless steel for resistance to the ICC have shown that it is not appropriate to use welded inconel 718 for the impeller, it is advisable to use material that would ensure uninterrupted operation in a corrosive environment at cryogenic temperatures. Based on the working conditions of the parts, it is most expedient to make it from heat-resistant chromium-nickel alloys, namely, from float inconel 718 which meets the necessary strength characteristics. The recommended soldering mode is heating up to 950 ± 10 oC, holding for 30 minutes from the moment of loading into the oven, cooling to 3000C with the oven, further in the air, since it has less influence on the corrosion resistance of steels in stainless steel joints. Quality control of inconel 718 alloy by GOST methods similar to that used for the control of X67MBHT type alloys showed the results similar to those obtained by the ASTM and AMS control methods.