Abstract:Introduction. It is noted that the chip is an undesirable type of metal scrap, because it has a developed surface, which creates conditions for more intense interaction with the surrounding atmosphere. This creates conditions for oxidation and gas saturation, especially at elevated temperatures typical of remelting processes. Therefore, the process of chip utilizing is considered, bypassing the remelting stage. The aim of the work is to establish the level of work hardening of chips during the processing of aluminum alloys and to predict its effect on the subsequent processing process. Research methods: to assess the deformed state, the finite element method was applied, implemented in the RAPID-2D software package. The sequence of actions included the creation of the initial shape of the deformation region and the configuration of the tool. The mutual displacement of the tool and the deformable material is specified using the corresponding boundary conditions. The deformable medium is a viscous-plastic material with power-law hardening, the physical and mechanical properties correspond to an aluminum-magnesium alloy. Results and discussion: the solution obtained shows that the degree of shear deformation in the chips can reach a value of more than 2. In this case, a higher level of deformation is localized on the side of the convex part of the chip. The comparison of the solution with those obtained earlier by other authors is carried out and its similarity is shown. In the considered solution, the difference in the degree of work-hardening of the chips along its thickness is 36 %. A variant of the sequence of processing the workpiece first by cold deformation, and then by cutting is considered. The field of application of the results of the work is the development of methods for the processing of technogenic formations. Conclusions. During the cutting process, the plastic deformation of the chips reaches significant values. In this paper, the difference in the degree of shear deformation in the chip thickness is established, depending on the proximity of the cut layer to the surface of the cutting tool. It is proposed to take this difference into account at the subsequent stages of chip processing. The presence of the marked inhomogeneity of mechanical properties leads to consequences in the form of an inhomogeneous distribution of the temperature of the beginning of recrystallization during subsequent operations of heat treatment or hot deformation treatment. The principle of additivity of the degree of deformation obtained by the metal at the stage of plastic shaping of the workpiece and the shaping of the chip itself is introduced.

EVALUATION OF HARDENING EFFICIENCY WITH CONVECTIVE HEAT AND MASS TRANSFER MECHANISM DURING LASER SURFACE ALLOYING IN REFLOW MODE

THE MODERN LASER METHODS OF MACHINE AND TOOL PARTS HARDENING ANALYSIS

Combining Ultrafast Laser Texturing and Laser Hardening to Enhance Surface Durability by Improving Hardness and Wear Performance

Development of a combined technology for hardening the surface layer of steel 38Cr2MoAl

Multi-objective Numerical Simulation of Geometrical Characteristics of Laser Cladding of Cobalt-Based Alloy Based on Response Surface Methodology

SELECTIVE SURFACE HARDENING OF GEAR MECHANISM SHAFT BY ROBOTIC LASER 3D SYSTEM

Correlation between Wear Resistance of High-Speed Steel R6M5 and Deformations Arising during Laser Hardening

Evaluation of the level of hardening of aluminum alloy chips intended for subsequent pressure treatment

Effects of laser heat treatment combined with ultrasonic impact treatment on the surface topography and hardness of carbon steel AISI 1045

Influence of the initial structure on the efficiency of laser processing of steel

Effect of Combined Laser Thermal and Shock Wave Effects on the Mechanical and Tribological Properties of Steels

Effect of Process Parameters on the Hardness of Laser Surface Textured 5A06 Aluminum Alloy

Laser Melting and Surface Texture Technology: Effect on Friction Properties

LASER HARDENING PROCESS ON Ck 45 DEPENDING ON THE LASER PARAMETERS - a small review

Surface integrity of laser-assisted turning of the GH4169 alloy

Analysis of the Advantages of Laser Processing of Aerospace Materials Using Diffractive Optics

Development of Hardening Technology for Oil and Gas Pumping and Compressor Equipment Using Laser Hardening

Layered hardening and grain structure refinement of low-alloyed tool steel applying two-stage surface morphology modification by laser phase transformation and ultrasonic peening

Laser-induced softening analysis of a hardened aluminum alloy by physical simulation

Experimental and Statistical Analysis of the Effect of Heat Treatment on Surface Roughness and Mechanical Properties of Thin-Walled Samples Obtained by Selective Laser Melting from the Material AlSi10Mg

Laser Surface Transformation Hardening for Automotive Metals: Recent Progress