Abstract:This Ph.D. research is based on the development of novel sol-gel techniques for synthesis of nanostructured ultra high temperature ceramics (UHTCs) and subsequent spark plasma sintering (SPS) for densifying the UHTC composites. The liquid nature of the sol-gel process offers advantages such as high purity and ability for mixing and infiltration, and thus it can overcome some shortcomings of the conventional power processing of ceramics. SPS delivers microstructures with good density and fine grain size due to its internal heat generation, high heating rate and short sintering time required. Titanium carbide (TiC) and zirconium diboride (ZrB₂) are selected as the UHTC matrix materials to form composites with different kinds of carbon based materials, including 1D carbon nanotubes (CNTs), 1D chopped carbon fibers, 2D woven and 3D needle-punched carbon fiber fabrics, and 3D graphene networks. One challenge to form the composites by conventional powder processing is the difficulty to achieve a homogeneous mix of ceramic powders and the carbon materials. The aim of this research is to take the advantages of sol-gel processing to synthesize nanostructured carbon reinforced UHTC composites with improved microstructures, mechanical and/or other properties. Graphene/TiC composites were synthesized through sol-gel infiltration of graphene network sponges. The C/Ti ratio of the sol-gel solutions influenced the composition as well as the microstructure of the composites. Graphene sheets could react with titanium dioxide (TiO₂) during the carbothermal reduction, forming a plate-like structure when the carbon content in the sol was low. The samples after SPS sintering showed interesting microstructures of nanostructured TiC surrounded by a network of graphene sheets. The composites were toughened by debonding and bridging of the graphene sheets. It was also proved that the composites exhibited an energy absorption mechanism under impact. CNT/TiC composites were prepared by sol-gel mixing and SPS sintering. The application of sol-gel gave an advantage in homogenous mixing. CNTs were able to toughen the composite by bridging, pullout and crack deflection. The fracture toughness increased with the amount of CNTs, but sacrificing the hardness of the materials. A CNTs containing TiC based sol was coated on ZrB₂ raw powders, forming a homogeneous microstructures after sintering, where most of the TiC grains and CNTs were distributed at the grain boundaries of ZrB₂, forming weak interfaces, which benefited the toughness through crack deflection and impact absorption. The chopped carbon fibers had similar toughening effect to CNTs in the composites. Different types of coatings on the surface of carbon fibers influenced the interface properties between ceramic matrix and fibers, thus affecting the fiber pullout and debonding. Sol-gel infiltration was applied to synthesize ceramic composites with 2D woven and 3D needle-punched carbon fiber fabrics. The results showed that sol-gel infiltration was a much more effective way to uniformly fill the fine pores between fiber filaments than the conventional powder slurry infiltration method. The composites showed improved fracture toughness as a result of fiber pullout, debonding, and crack deflection.

Unravelling the optimization of few-layer graphene crystallinity and electrical conductivity in ceramic composites by Raman spectroscopy

Critical Influence of the Processing Route on the Mechanical Properties of Zirconia Composites with Graphene Nanoplatelets

Enhanced Toughness Of Zirconia Ceramics With Graphene Platelets Consolidated By Spark Plasma Sintering

Sintering Behavior, Microstructure and Mechanical Properties of Various Fluorine-Containing Y-SiAlON Glass-Ceramics

In-situ preparation of fully stabilized graphene/cubic-leucite composite through graphene oxide/geopolymer

Ambient Flash Sintering of Reduced Graphene Oxide/zirconia Composites: Role of Reduced Graphene Oxide

Sol–gel method and reactive SPS for novel alumina-graphene ceramic composites

Physical characterization of composites based on yttria‐stabilized zirconia and doped lanthanum gallate

Microstructure and mechanical properties of a porous ceramic composite with needle‐like mullite and zirconia

Synthesis, microstructure, and electromagnetic behavior of graphene nanoplatelets/CZCF ferrite nanocomposites

Electrostatic Assembly Preparation of High-Toughness Zirconium Diboride-Based Ceramic Composites with Enhanced Thermal Shock Resistance Performance

Sol-gel synthesis of carbon based materials reinforced ultra high temperature ceramic composites

Effect of morphology and defectiveness of graphene-related materials on the electrical and thermal conductivity of their polymer nanocomposites

The toughening mechanism and mechanical properties of graphene-reinforced zirconia ceramics by microwave sintering

High performance alumina based graphene nanocomposites with novel electrical and dielectric properties

Enhancing electrical conductivity in zirconium-doped SiC ceramics through synergistic effects of crystal structure and free carbon control

Effects of composite nucleating agents on crystallization behavior and properties of fluorphlogopite glass-ceramics

Ultrasonication Influence on the Morphological Characteristics of Graphene Nanoplatelet Nanocomposites and Their Electrical and Electromagnetic Interference Shielding Behavior

X-ray Photoelectron Spectroscopy Analysis of Scandia-Ceria-Stabilized Zirconia Composites with Different Transport Properties

Enhancing the Properties of Yttria-Stabilized Zirconia Composites with Zeolitic Imidazolate Framework-Derived Nanocarbons

Enhancing microstructure homogeneity and electrical conductivity in flash-sintered 8YSZ: Impact of electric-current ramp control and thermal insulation