Abstract:This paper mainly investigates the aerodynamic effect of two different average sizes and three specific nonaxisymmetric rotor tip clearance arrangements on the overall performance and loss mechanism of a four-stage low-speed research compressor (LSRC) at Shanghai Jiao Tong University. The stage was modeled for the steady simulations as a seventh entire annulus computation domain of the inlet vane and the first stage rotor row. The numerical method was validated using experimental data on the radial profiles of total pressure and flow angle at the rotor outlet. Results illustrate that a size increase (from 1.2% span to 2.3% span) in uniform clearance layout will bring adverse effects. The specific degradation in isentropic efficiency is 1.11% and 1.77% at the design and near stall points, respectively. The nonaxisymmetric rotor tip clearance arrangement significantly increases the stall margin by 25%-31% relative to the uniform layout, and the benefit is more pronounced in the case of a larger average clearance size of 48%-57%. However, there are no visible changes in the global performance characteristics. The zigzag-distributed clearance layout has a better performance impact than the other two linearly arranged schemes. Detailed analyses based on the streamwise and spanwise efficiency deviation were carried out to interpret the aerodynamic improvement. Moreover, the differentiated distribution of aerodynamics and specific flow behaviors at the rotor tip were investigated in detail over each rotor passage. Circumferentially averaged performance and radial profiles were performed. Because of the nonaxisymmetric layout, the inlet mass flow and incidence were redistributed in both radial and circumferential directions, further causing a significant alleviation of the blockage arising from the tip leakage flow, especially the region at the first 0.5 axial chord and above 80% span. The loss caused by the nonaxisymmetric tip clearance included not only the leakage flow loss, but also the interference between the leakage flow and the incoming main flow, or the low-energy fluid in the corner region of the casing, and even the loss on the suction surface of the adjacent rotor blade.

Mechanism Analysis of the Influence of Blade Thickness Deviation on The Performance of Axial Flow Compressor

Effect and Mechanism of Roughness on the Performance of a Five-Stage Axial Flow Compressor

Mechanism Analysis and Uncertainty Quantification of Blade Thickness Deviation on Rotor Performance

Uncertainty Quantification on the Influence of Blade Thickness Deviation at Different Rotational Speeds Based on Flow Dissipation Analysis

The Analysis of Attenuated Blade Tip Mechanism on Axial Compressor Rotor

Analysis of the Influence of Blade's Machining Error on Aerodynamic Performance of Impeller Based on NUMECA

Analysis of Overall Aerodynamic Performance of Axial-Flow Compressor with Attenuated Blade Tip

Numerical Investigation into the Mechanism Regarding the Inception and Evolution of Flow Unsteadiness Induced by the Tip Leakage Flow in a Transonic Compressor

Influence of Variable-Thickness Blade on Structural Strength and Performance of Centrifugal Compressor

Investigation on the Influence of the Structure Parameters of Blade Tip Recess on the Performance of Axial Flow Compressor

The Influence of Blade Root Fillet and Blade Tip Clearance on the Aerodynamic Performance of a Transonic Axial Compressor

Influence of Local Surface Roughness of Rotor Blade on Performance of an Axial Compressor Stage

Overall Performance and Loss Analysis of a Low-Speed Research Compressor with Different Nonaxisymmetric Tip Clearance Layouts

Impact of Defective Blades on Aerodynamic Performance of Transonic Compressor Rotor

A High-Loaded Axial Compressor Bifurcate Stator Blade Aerodynamic Design And Vorticity Dynamics Diagnosis For Flow Structure

Investigation on the Mechanism of Blade Tip Recess Improving the Aerodynamic Performance of Transonic Axial Flow Compressor

Numerical Investigation of the Influence of Axial Overlap of Blade Angle Slots on an Axial Flow Compressor Stability

The Effects of Stepped Tip Gap on Performance and Flowfield of A Subsonic Axial-Flow Compressor Rotor

Investigation on Aerodynamic Performance of a Centrifugal Compressor with Leaned and Bowed 3D Blades

Numerical study on the effect of blade tip clearance change on stall margin of the transonic axial flow compressor rotor

Stall Inception Analysis on Axial Compressors with Different Rotor Loading Distributions under Radial Inlet Distortions