Abstract:In this study, aerial fireworks commonly used for celebrations in Taiwan were analyzed. These fireworks have propellant components, which are stored under varying humidity and temperature conditions. Differential scanning calorimetry (DSC) and the Vent Sizing Package 2 (VSP2) were used to assess the relationship between microscale heat transfer and temperature as well as thermal runaway in an adiabatic environment. Thermodynamic methods, namely the Friedman, Flynn–Wall–Ozawa, and ASTM E698, were used to analyze the safety and latent thermal hazards of aerial fireworks. DSC experiments confirmed the high solubility of potassium nitrate (KNO3), which enables it to readily dissolve in K+ and NO3-documentclass[12pt]{minimal}usepackage{amsmath}usepackage{wasysym}usepackage{amsfonts}usepackage{amssymb}usepackage{amsbsy}usepackage{mathrsfs}usepackage{upgreek}setlength{oddsidemargin}{-69pt}egin{document}$$ ext{NO}^{-}_3$$end{document}. Increasing the relative humidity and exposure time caused the surface of the oxidizer to dissolve, resulting in the reduction of the second exothermic peak and, in turn, incomplete combustion and launch failure. The results obtained using the ASTM E698 method revealed that when the samples were soaked in deionized (DI) water, their apparent activation energy increased considerably from 45.78 to 153.68 kJ mol−1, reflecting a decrease in the temperature sensitivity of the gunpowder in the fireworks. To reduce the reactivity of the gunpowder and minimize the thermal hazard associated with fireworks, a large amount of water must be added. However, the experiment performed using VSP2 showed that when the humidity increased, the adiabatic exothermic onset temperature was delayed. The maximum temperature of the original sample was the highest. The maximum reaction rate of the samples stored at a relative humidity of 40% was shorter than that of other samples, and that of the samples soaked in DI water was the longest. Regarding the relationship between pressure rise rate and temperature, (dP/dt)max can be used to determine whether the propulsion capacity of a firework during ignition is sufficient. When DI water was added, the propulsion capacity decreased, and fireworks could not be ignited. The samples stored at a relative humidity of 40% had higher pressure than did the original sample. The samples soaked in DI water had lower pressure than did the original sample. These results indicate that increasing humidity affects temperature and pressure.

Interpretation of safe parameters of chemical compositions and noise level of the fireworks crackers

Evaluation of the suitable analytical techniques for the investigation of the toxic elements and compounds in the Pyrotechnic materials (Green crackers)

A preliminary study of combustion flame by digital image processing and residue for fireworks flash powder

A study of thermal and safety behaviour of potassium nitrate in flash powder after surface modification for prevention of self-decomposition due to hygroscopic effect

Study on the Impact of Firecrackers on Atmospheric Pollutants during Diwali Festival in Tamil Nadu, India

A novel environmental-friendly and safe unpacking powder without magnesium, aluminum and sulphur for fireworks

Experimentation on Sargassum wightii as a flash powder igniter for attaining eco-friendly combustion on pyrotechnics

Research of critical ambient temperature of cylindrical fireworks and crackers

Performance Study of Eco‐Friendly and Safe Pyrotechnics for Fireworks

Revealing the components and thermal hazard characteristics of traditional spark and cold light fireworks

Effect of relative humidity on the emission height and reaction force of single-tube fireworks

The Diwali festival: short-term high effect of fireworks emissions on particulates and their associated empirically calculated health risk assessment at Bhubaneswar city

Assessment of pollution by the combustion residue and smoke of boron blended flash powder

Effect of emulsifiers on the thermal stability of firework propellants

Thermal explosion model and calculation of sphere fireworks and crackers

Applications of intrinsic safety characteristic parameters of propellant dust: Commercial multi-tube pyrotechnic hazard assessment

Source apportionment of metal ions in ambient air (PM 2.5 ) during firecracker bursting: A case study of Amritsar Diwali on 24 October 2022

Thermal decomposition and evaluation thermokinetic parameters for explosive type

Assessment of ambient air quality in relation to the burning of firecrackers during the festival of Diwali: A case study of Jodhpur City (India)

Taguchi method-based evaluation of thermal hazard of lift-off pyrotechnics under various storage conditions

Modeling and calculation of thermal explosion time to ignition of cylindrical fireworks and crackers