Abstract:<p>Biodiesel is a promising alternative fuel for diesel engines, but its high viscosity and low volatility have limitations in decreasing emissions. As a renewable alternative fuel with a high oxygen content, ethanol blended with biodiesel can decrease kinematic viscosity and improve fuel evaporation. In this study, the effects of the ethanol addition ratio on the spray, combustion, and emission performances of a diesel engine fuelled with biodiesel were investigated. The spray characteristics were measured using a high-speed camera and Malvern laser analysis, whereas the combustion and emission performances were tested on a turbocharged common rail direct injection (CRDI) diesel engine. The results show that adding ethanol to biodiesel enlarges the spray cone angle (SCA) and shortens spray tip penetration (STP). In addition, the curves of the size–volume distribution (SVD) of the atomized fuel droplets move toward a smaller diameter, and the Sauter mean diameter (SMD) of the biodiesel–ethanol (BE) blends gradually decreases with increasing ethanol proportion. At low loads, the fuel injection strategy is multi-injection, and the peak cylinder pressures (PCPs) of BE blends are 0.77–1.96% higher than that of diesel at different ethanol blending ratios. However, the peak heat release rates (PHRRs) of BE blends are 9.3–11.5% higher than that of diesel owing to a faster combustion rate, longer main-injection duration, and more hydroxyl radicals generated in the pilot-injection stage. At medium–high loads, the injection strategy changes to single injection, the PCPs of BE blends are roughly equivalent to that of diesel, and the PHRRs of BE blends for different ethanol blending ratios are 9.76–11.91% lower than that of diesel. This is because of the lower diffusion combustion ratio, lower heat value, and change of injection duration corresponding to the variation in fuel properties. In addition, the results of the peak pressure rise rate and the cyclic variation indicate that the higher ethanol addition ratio increases the combustion noise and decreases the combustion stability. In terms of exhaust emissions, compared with biodiesel, with increasing ethanol blending ratio, the soot emissions for different BE blends decrease by 11.28–47.23%, the NOx emissions increase by 2.68–7.04%, and the HC emissions increase by 9.99–21.47%. Considering the engine performance comprehensively, a 20% ethanol blending ratio in biodiesel is recommended.</p>

Expansion heat release and thermal efficiency of acetone-butanol-ethanol-diesel blended fuel (ABE20) combustion in piston engine

Combustion and emission characteristics of an Acetone-Butanol-Ethanol (ABE) spark ignition engine with hydrogen direct injection

Evaluation of Sooting Tendency of Acetone–butanol–ethanol (ABE) Fuels Blended with Diesel Fuel

Effect of Acetone-n-Butanol-Ethanol (ABE) As an Oxygenate on Combustion, Performance, and Emission Characteristics of a Spark Ignition Engine

Skeletal Mechanism Generation and Validation for Acetone–n-butanol–ethanol (ABE) Combustion in Diesel Engine

Effects of hydrogen direct injection on combustion and emission characteristics of a hydrogen/Acetone-Butanol-Ethanol dual-fuel spark ignition engine under lean-burn conditions

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

A synthetic skeletal mechanism for combustion simulation of acetone-n-butanol-ethanol mixture and its components in diesel engines

A skeletal chemical reaction mechanism for gasoline-ABE blends combustion in internal combustion engine

Combustion Characteristics of a Compression Ignition Engine Fuelled with Diesel/Ethanol Blends

Construction of a compact skeletal mechanism for acetone–n–butanol–ethanol (ABE)/diesel blends combustion in engines using a decoupling methodology

The experimental and numerical investigation of biofuels on combustion and tribology characteristics in a compression ignition engine

Emission Reduction Potential of Using Ethanol–biodiesel–diesel Fuel Blend on a Heavy-Duty Diesel Engine

Emission Characteristics Using Methyl Soyate-Ethanol-Diesel Fuel Blends on A Diesel Engine

Performance, Combustion, and Emission Comparisons of a High-Speed Diesel Engine Fueled with Biodiesel with Different Ethanol Addition Ratios Based on a Combined Kinetic Mechanism

Experimental study on spray characteristics, combustion stability, and emission performance of a CRDI diesel engine operated with biodiesel–ethanol blends

Impact of Lower and Higher Alcohol Additions to Diesel on the Combustion and Emissions of a Direct-Injection Diesel Engine

Skeletal Mechanism for I-Propanol-n-butanol-ethanol (IBE) and N-Butanol Combustion in Diesel Engine

Heat Release Rate and Combustion Characteristic Analysis of Diesel Engine Fuelled with Ethanol-Diesel Blend Fue

Combustion and Emission Characteristics of Diesel Engine Fueled with Biodiesel/pode Blends

Environmental and performance impacts of 2-ethylhexyl nitrate and ethanol in diesel blends: A comprehensive study