Abstract:Abstract — Fluorocarbon ‘O’-rings to DTD5612A:1982 have been used for many years for sealing at −40°C. The UK Department for Transport (DfT) issued a letter on 12 March 2001 raising concerns over the suitability of these ‘O’-rings for service temperatures down to −40°C as required by the regulations for certain types of packages containing radioactive material, and requested that the technical justification for continued use was reviewed. Gravatom Engineering Systems Ltd performed a low-temperature test, at Harwell, using design no 3406 with new fluorocarbon ‘O’-rings and bolts. The test proved that these ‘O’-rings are not suitable for temperatures down to −40°C since the seals would not hold a vacuum at temperatures lower than −24°C. This necessitated an investigation to find a suitable ‘O’-ring material with a leak rate pelformance of 10−5 Pa.m3. s−1 SLR at −40°C to +330°C since this represents the widest temperature range of the AWE Type B(U) containers. Various seal manufacturers were contacted, and following further investigation two seal materials presented themselves as possible options: Viton GLT, a fluorocarbon manufactured by Parker-USA (Parker compound V0835–75) with CEETAK Ltd acting as agents in the UK, and EPDM-30H developed by BNFL and manufactured by James Walker & Co Ltd. Following testing, the EPDM-30H seals proved to be the most suitable sealing material option for an operating temperature range of −40°C to +330°C. The seal achieved a leak rate at −40°C of better than 8.0 × 10−10 Pa.m3.s−1 which is well within the equivalent target leak rate of less than 1.2 × 10−4 Pa. m3.s−1. The seals also remained effective down to at least −50°C with no loss in sealing pelformance. A leak rate of better than 7.2 × 10−6 Pa.m3.s−1. was achieved at +330°C which is within the target leak rate of less than 6.4 × 10m−5 Pa.mm3.s−1. The interspace pressure increased slightly during heating, but recovered fully on cooling to give a leak rate at ambient temperature of 1.0 × 10−10 Pa.mm3.s−1. The EPDM-30H seals proved satisfactory at high temperature, with excellent recovery on cooling. It was concluded that EPDM-30H seals may be used as a direct replacement for Viton where the temperature range does not exceed −40°C to +330°C and where the higher temperature of that range is of relatively short duration (i.e. less than 24 h).

A Simple Testing Method for the Cold Flexibility of an O-Ring Packing

Experimental Research and Finite Element Analysis of Seals in the Pressure Compensator

LOW TEMPERATURE SEALING BEHAVIOR EVALUATION OF ELASTOMERS IN AIRCRAFT HYDRAULIC SYSTEMS

Effect of stress relaxation on the sealing performance of O-rings in deep-sea hydraulic systems: A numerical investigation

Analysis of material fault of O-ring seal in aircraft cylinder

Experimental Study of Reciprocating Sealing Performance of Nitrile Rubber O-ring

Research on the Influence of Extremely Cold Environment on the Performance of Silicone Rubber and Fluorinated Silicone Rubber

Experimental Study of the Mechanical Properties of Full-Scale Rubber Bearings at 23 °C, 0 °C, and −20 °C

Apparatus for material tests using an internal loading system in high-pressure gas at room temperature

Friction and wear properties of several rubber materials for high pressure O-ring

Long-term sealing performance evaluation and service life prediction of O-rings under thermal-mechanical coupling conditions

Investigation into Replacement of Viton ‘O’-Rings

Investigation of Static and Dynamic Seal Performances of a Rubber O-Ring

Fretting behavior of static metal seal and testing apparatus for fretting friction with low/high temperature

Experimental and thermal‐structure coupling analysis for oil and water‐swellable packer

Analysis of O-Ring Seal Failure under Static Conditions and Determination of End-of-Lifetime Criterion

Stress Analysis and Sealing Capability Research of Rubber Sealing O-Ring for Static Sealing

Proposal of New Test Method of Open Hole Compression (OHC) and Results of Round Robin Tests for Standardization

Study on the aging of three typical rubber materials under high- and low-temperature cyclic environment

Experimental Tensile Strength Analysis of Different Manufacturer Oring