Abstract:The ultrafine composite fibers based on the composites of binary fatty acid eutectics and polyethylene terephthalate (PET) with varied fatty acid eutectics/PET mass ratios (50/100, 70/100, 100/100 and 120/100) were fabricated using the technique of electrospinning as form-stable phase change materials (PCMs). The five binary fatty acid eutectics including LA-MA, LA-PA, MA-PA, MA-SA and PA-SA were prepared according to Schrader equation, and then were selected as an innovative type of solid-liquid PCMs. The results characterized by differential scanning calorimeter (DSC) indicated that the prepared binary fatty acid eutectics with low phase transition temperatures and high heat enthalpies for climatic requirements were more suitable for applications in building energy storage. The structural morphologies, thermal energy storage and thermal stability properties of the ultrafine composite fibers were investigated by scanning electron microscope (SEM), DSC and thermogravimetric analysis (TGA), respectively. SEM images revealed that the electrospun binary fatty acid eutectics/PET ultrafine composite fibers possessed the wrinkled surfaces morphologies compared with the neat PET fibers with cylindrical shape and smooth surfaces; the grooves or ridges on the corrugated surface of the ultrafine composite fibers became more and more prominent with increasing fatty acid eutectics amount in the composite fibers. The fibers with the low mass ratio maintained good structural morphologies while the quality became worse when the mass ratio is too high (more than 100/100). DSC measurements suggested that the heat enthalpies of melting and crystallization of the ultrafine composite fibers increased gradually with increasing fatty acid eutectics amounts, but their phase transition temperatures had almost no obvious variation as relative to the corresponding fatty acid eutectics. Meanwhile, the characteristic temperatures and heat enthalpies of the ultrafine composite fibers varied with the different types of binary fatty acid eutectics. TGA results indicated that the degradation of electrospun binary fatty acid eutectics/PET ultrafine composite fibers with representative mass ratio of 100/100 had two steps and corresponded respectively to the degradations of binary fatty acid eutectics and PET polymer chains; and the charred residue at 700 degrees C of the composite fibers was lower than that of the neat PET fibers. It could be envisioned that the electrospun binary fatty acid eutectics/PET composite fibers would be extensively used for latent heat storage in the field of building energy conservation. (C) 2012 Elsevier Ltd. All rights reserved.

Fabrication and characterization of dual-functional ultrafine composite fibers with phase-change energy storage and luminescence properties

Fabrication, Structural Morphology and Thermal Energy Storage/Retrieval of Ultrafine Phase Change Fibres Consisting of Polyethylene Glycol and Polyamide 6 by Electrospinning

Electrospun Ultrafine Composite Fibers Consisting of Lauric Acid and Polyamide 6 As Form-Stable Phase Change Materials for Storage and Retrieval of Solar Thermal Energy

Flexible Polyethylene Glycol/polyvinylpyrrolidone Composite Phase Change Fibres: Preparation, Characterization, and Thermal Conductivity Enhancement

The Improvement Of Thermal Stability And Conductivity Via Incorporation Of Carbon Nanofibers Into Electrospun Ultrafine Composite Fibers Of Lauric Acid/Polyamide 6 Phase Change Materials For Thermal Energy Storage

Multicomponent Phase Change Microfibers Prepared by Temperature Control Multifluidic Electrospinning.

Ultrafine Lauric–myristic Acid Eutectic/poly (Meta-Phenylene Isophthalamide) Form-Stable Phase Change Fibers for Thermal Energy Storage by Electrospinning

Solid-solid phase change fibers with enhanced energy storage density for temperature management

Luminescence properties of composite nanofibers with different diameters prepared by electrospinning technology

Electrospinning Preparation and Properties of Magnetic-Photoluminescent Bifunctional Coaxial Nanofibers

Preparation, Morphology and Thermal Properties of Electrospun Fatty Acid Eutectics/polyethylene Terephthalate Form-Stable Phase Change Ultrafine Composite Fibers for Thermal Energy Storage

Fabrication and characterization of Polyvinylidene fluoride and Myristic acid-Tetradecanol eutectic composite Nanofibers by electrospinning

Fabrication of luminescent hybrid fibres based on the encapsulation of polyoxometalate into polymer matrices

Emulsion-Electrospinning N-Octadecane/Silk Composite Fiber As Environmental-Friendly Form-Stable Phase Change Materials

Flexible Janus Nanofibers: Facile Electrospinning Construction and Enhanced Luminescent–Electrical–Magnetic Trifunctionality

Electrospinning Preparation, Structure, and Properties of Fe3O4/Tb(acac)3phen/Polystyrene Bifunctional Microfibers

Electrospun Ultrafine Composite Fibers Of Binary Fatty Acid Eutectics And Polyethylene Terephthalate As Innovative Form-Stable Phase Change Materials For Storage And Retrieval Of Thermal Energy

Water-soluble Luminescent‐electrical‐magnetic Trifunctional Composite Nanofibers Prepared Via Electrospinning Technique

Review on Electrospun Ultrafine Phase Change Fibers (pcfs) for Thermal Energy Storage

Cooperative In Situ Impregnation of PEG and Au Nanoparticles into Expanded CNT Network Toward Composite Phase Change Fibers with High Storage Capacity and Photothermal Conversion

Novel pyrene-based aggregation-induced emission luminogen (AIEgen) composite phase change fibers with satisfactory fluorescence anti-counterfeiting, temperature sensing, and high-temperature warning functions for solar-thermal energy storage