Abstract:Abstract The LBE- or Lead-cooled fast reactor (LFR) is an important candidate reactor for the Generation-IV nuclear energy systems, where the Molten Fuel-Coolant Interaction (MFCI) process differs from that occurred in light water reactors and sodium cooled fast reactors due to the coolant property differences. In the lack of experimental and numerical studies on MFCI process in LFRs, the experiments under eight conditions with different initial temperatures of molten metal and different depth of coolant pool are conducted in this study to research the interaction between molten stainless steel (SS) and liquid Lead Bismuth Eutectic (LBE) coolant, where the radial and axial temperature distribution data of the LBE pool are obtained to validate a 2D multiphase fluid dynamics code named ACENA, which is preliminarily developed to simulate severe accidents phenomena for heavy liquid metal cooled fast reactors. A brief description of theoretical models employed in the ACENA code is listed in this study. The comparison results show the ACENA code could attain acceptable accuracy in simulating flow and heat transfer characteristics of MFCI process. The calculated values of temperature growth peak in the LBE pool are in good agreement with the experimental data. The overall maximum deviation between the calculated and experimental temperature increase values is within the range of 10–30 K. The maximum pressure surge of the argon atmosphere covering the LBE pool does not exceed the safety limit of the reaction vessel predicted by the ACENA code corresponding to the experiment conditions. However, due to the severe electromagnetic interference during the induction heating process in experiments, the relatively accurate pressure fluctuation data were failed to be collected. According to this study, the shortcomings of the current numerical work are summarized as follows: (1) The code assumes the molten material could be fully mixed with the coolant in the control grid, so the solidification and fragmentation phenomena of the molten material could not be realistically simulated, especially for the large-sized products obtained from experiments; (2) The code assumes the reaction vessel is adiabatic and the temperature distribution of the LBE pool is uniform, but actually the temperature of LBE pool was manually adjusted to approximate thermal equilibrium. Additionally, due to the heat dissipation of the molten SS in the crucible, a thermal stratification phenomenon occurred in the LBE pool; (3) The code employs empirical formulas validated in SFRs research, while due to the physical property differences of sodium and LBE, the empirical formulas may not be completely applicable to LFRs if only by simply extrapolating. Therefore, further experimental studies and improvement of physical models are necessary for excavating potential of the ACENA code, which could close some research gaps for accident safety analysis of LFRs.

Test problem for thermal-hydraulics and neutronic coupled calculation fore ALFREAD reactor core

Neutronic investigation of ALFRED lead-Cooled fast reactor core using monte carlo modeling

Development of a New Thermal-Hydraulic Module for FRENETIC, a Code for the Multiphysics Analysis of Liquid Metal–Cooled Reactors

Analysis of the experimental tests performed at NACIE-UP facility through a novel CFX-RELAP5 codes coupling

Coupling of Neutronics and Thermal-Hydraulics Codes for the Simulation of Reactivity Insertion Accident for LFR

Development and Preliminary Verification of a Neutronics-Thermal Hydraulics Coupling Code for Research Reactors with Unstructured Meshes

Core thermal hydraulic CFD support for liquid metal reactors

Neutronics and thermal-hydraulics coupling analysis using the FLUENT code and the RELAP5-3D code for a molten salt fast reactor

Thermal-hydraulics/thermal-mechanics temporal coupling for unprotected loss of flow accidents simulations on a SFR

MULTIPHYSICS MODELISATION OF AN UNPROTECTED LOSS OF FLOW TRANSIENT IN A SODIUM COOLED FAST REACTORS USING A NEUTRONIC-THERMAL-HYDRAULIC COUPLING SCHEME

Neutronics and Thermo-Fluids Simulation of Generic Pebble-Bed Fluoride-Salt-Cooled High-Temperature Reactor

Overview on Lead-Cooled Fast Reactor Design and Related Technologies Development in ENEA

Application of Full-Core Three-Dimensional Multi-Physics Calculation to the EBR-II SHRT-45R Benchmark

The Development of Nuclear Reactor Three-Dimensional Neutronic Thermal–hydraulic Coupling Code: CorTAF-2.0

Three Dimensional Neutronic/thermal-Hydraulic Coupled Simulation of MSR in Transient State Condition

CorTAF-LBE: A Full Scale Subchannel-Level Thermal-Hydraulic Characteristics Analysis Code for LBR Core Based on OpenFOAM

Full-scale Neutronic/thermal–hydraulic Coupling Analysis of Plate-Type Reactor Based on RMC and MOOSE

Numerical Study on Molten Stainless Steel and Lead Bismuth Eutectic Interaction for Lead-Cooled Fast Reactors Using the ACENA Code with Experimental Validation

Development and verification of a neutronics-thermal hydraulics coupling code with unstructured meshes neutron transport model

Core calculations of the Molten Salt Fast Reactor using different computational codes

Development and Validation of the Lead-Bismuth Cooled Reactor System Code Based on a Fully Implicit Homogeneous Flow Model