Abstract:A series of composites based on epoxy resin filled with additives of natural origin were prepared to investigate the influence of such fillers on the properties of the epoxy compositions. For this purpose, the composites containing 5 and 10 wt.% of additive of natural origin were obtained using the dispersion of oak wood waste and peanut shells in bisphenol A epoxy resin cured with isophorone-diamine. The oak waste filler had been obtained during the assembly of the raw wooden floor. The performed studies include testing of samples prepared using unmodified and chemically modified additives. Chemical modification via mercerization and silanization was performed to increase the poor compatibility between the highly hydrophilic fillers of natural origin and the hydrophobic polymer matrix. Additionally, the introduction of NH2 groups to the structure of modified filler via 3-aminopropyltriethoxysilane, potentially takes a part in co-crosslinking with the epoxy resin. Fourier Transformed Infrared Spectroscopy (FT-IR), as well as Scanning Electron Microscopy (SEM), were carried out, to study the influence of performed chemical modification on the chemical structure and morphology of wood and peanut shell flour. SEM analyses showed significant changes in the morphology of compositions with chemically modified fillers, indicating improved adhesion of the resin to lignocellulosic waste particles. Moreover, a series of mechanical (hardness, tensile strength, flexural strength, compressive strength, and impact strength) tests were carried out, to assess the influence of the application of fillers of natural origin on the properties of epoxy compositions. All composites with lignocellulosic filler were characterized by higher compressive strength (64.2 MPa-5%U-OF, 66.4%-SilOF, 63.2-5%U-PSF, and 63.8-5%SilPSF, respectively), compared to the values recorded for the reference epoxy composition without lignocellulosic filler (59.0 MPa-REF). The highest compressive strength, among all tested samples, was recorded for the composite filled with 10 wt.% of unmodified oak flour (69.1 MPa-10%U-OF). Additionally, higher values of flexural and impact strength, concerning pure BPA-based epoxy resin, were recorded for the composites with oak filler (respectively, flexural strength: 73.8 MPa-5%U-OF and 71.5 MPa-REF; impact strength: 15.82 kJ/m2-5%U-OF, 9.15 kJ/m2-REF). Epoxy composites with such mechanical properties might be considered as broadly understood construction materials. Moreover, samples containing wood flour as a filler exhibit better mechanical properties compared to those with peanut shell flour (tensile strength for samples containing post-mercerization filler: 48.04 MPa and 40.54 MPa; while post-silanization 53.53 MPa and 42.74 MPa for compositions containing 5 wt.% of wood and peanut shell flour, respectively). At the same time, it was found that increasing the weight share of flour of natural origin in both cases resulted in the deterioration of mechanical properties.

Effect of Adhesion Between Submicron Filler Particles and a Polymeric Matrix on the Structure and Mechanical Properties of Epoxy-Resin-Based Compositions

Improving Insulation Properties of Epoxy Filled with Surface Fluorinated Polystyrene Nanospheres

Epoxy resin mechanical properties in composition with copper (I) oxide particles, encapsulated by polylactide with variable thickness

The Influence of the Dispersed Filler of the Ni–Fe–Si–C System on the Physicomechanical Properties and Structure of Epoxy Composites

Influence of Interfacial Adhesion on Stress-Strain Properties of Highly Filled Polyethylene

Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres

Enhancement of Mechanical Properties and Bonding Properties of Flake-Zinc-Powder-Modified Epoxy Resin Composites

Effect of silica particle size and filler content on the fracture properties of epoxy resin composite

Synthesis and mechanical properties of the epoxy resin composites filled with sol−gel derived ZrO 2 nanoparticles

Synergistic Toughening and Strengthening of an Epoxy Resin Modified by the Simultaneous Use of Two Different Modifiers

Study of Epoxy Resin Composites Doped with Nonlinear Fillers and Its Electrical Properties

Modification of Epoxy Compositions by the Application of Various Fillers of Natural Origin

Modification of Epoxy Resin with Silica Nanoparticles and Process Engineering of Composites Based on Them

Preparation and Properties of Polymer Microspheres Filled Epoxy Composite Films by Uv-Curable Polymerization

Dielectric properties and thermal conductivity of epoxy resin composite modified by Zn/ZnO/Al 2 O 3 core–shell particles

Synergetic Enhancement of Mechanical and Electrical Strength in Epoxy/silica Nanocomposites Via Chemically-Bonded Interface

Design, Preparation and Characterization of a High-Performance Epoxy Adhesive with Poly (Butylacrylate-block-styrene) Block Copolymer and Zirconia Nano Particles in Aluminum- Aluminum Bonded Joints

Epoxy nanocomposites with high mechanical and tribological performance

Synergistic Effect of Organic and Inorganic Nano Fillers on the Dielectric and Mechanical Properties of Epoxy Composites

Research on improving the insulation properties of epoxy filled with surface fluorinated polystyrene nanospheres

Preparation and Mechanics Properties of the EP/ZnO Nanocomposites