Abstract:Phase change materials (PCMs) are widely employed in electronic thermal control systems for spacecraft because of their substantial energy storage competencies. Hence, the impact of gravitational acceleration (GA) on PCM thermal performance holds particular significance. Moreover, given considerations for spacecraft center of gravity, attitude control, and structural design, choosing an optimal battery placement orientation becomes pivotal for maximizing available space utilization. This study employs the enthalpy-porosity method to simulate and assess the heat transfer efficiency of PCM and the thermal behavior of cooling battery thermal management system (BTMS) under different gravity environments (0.05 g, 0.1 g, 1 g, 10 g, and 20 g) and different inclination angles ( θ = 90°, 45°, 0°). The research findings indicate that when θ = 90°, as gravity increases from 0.05g to 20g, the complete melting time of PCM at GA = 20g is shortened by 95.05 s (15.00 %) compared to GA = 0.05g. Particularly, when GA = 10 g, increasing θ from 45° to 90° reduces PCM melting time by 59.05 s (9.66 % reduction) compared to θ = 45°, while at θ = 0°, it decreases by 65.75 s (10.75 % reduction). Notably, at θ = 45°, some unmelted solid PCM accumulates in the lower right corner of the enclosure hindering the BTMS heat transfer. Based on PCM melting characteristics, three optimization structures for different θ are proposed. At t = 240 s, PCM melting significantly improves with fins. Comparing Convective Heat Transfer Coefficients (CHTC) curves before and after optimization reveals reduced accumulated effects. However, more fins aren't always better due to BTMS weight considerations. Investigating enhanced CHTC, fin mass, and volume ratio( γ ), the optimized model impacts BTMS weight differently for θ values. θ = 45°, a combination of annular and straight fins, is determined optimal using entropy-weighted TOPSIS. This paper innovatively studies PCM melting in BTMS under varied gravitational environments and θ , proposing an enhanced heat transfer scheme for aerospace BTMS design.

Experimental study on the heat transfer performance of a phase change material based pin-fin heat sink for heat dissipation in airborne equipment under hypergravity

Melting behavior and heat transfer performance in a modified PCM-filled enclosure with fins under hypergravity conditions

Effect of the inclination angle on the transient performance of a phase change material-based heat sink under pulsed heat loads

Numerical investigation on melting behaviour of phase change materials/metal foam composites under hypergravity conditions

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Transient thermal performance enhancement of phase change material (RT82) through novel pin arrangements under varied gravity conditions

Numerical Study on the Cooling Method of Phase Change Heat Exchange Unit with Layered Porous Media

Dynamic heat transfer characteristics of gravity heat pipe with heat storage

Experimental Investigation into the Effect of Fin Shapes on Heat Dissipation Performance of Phase Change Heat Sink

Thermal performance of a tandem-dual-channel flat-plate pulsating heat pipe applicable to hypergravity

Investigation of Gravity Effect on Phase Change Heat Transfer Using the Lattice Boltzmann Method

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Effect of Supergravity on Heat Transfer Characteristics of PCM with the Pore-Scale Lattice Boltzmann Method

Effects of Melting Temperature and the Presence of Internal Fins on the Performance of a Phase Change Material (Pcm)-Based Heat Sink

Thermal Performance of Heat Sink Filled with Double-Porosity Porous Aluminum Skeleton/Paraffin Phase Change Material

Numerical study and optimization of battery thermal management systems (BTMS) Based on Fin-Phase change material (PCM) in variable gravity environments

Experimental and numerical investigations on the intermittent heat transfer performance of rectangular cavity plate fin phase change material based heat sink

Thermal Performance Enhancement of Phase Change Material Heat Sinks for Thermal Management of Electronic Devices under Constant and Intermittent Power Loads

Buoyancy-driven melting and solidification heat transfer in finned latent heat storage units

Effect of melting temperature and amount of the phase change material (PCM) on thermal performance of hybrid heat sinks

Numerical study on electrohydrodynamic enhancement of PCM melting in cylindrical annulus under microgravity