Abstract:Purpose Since the biomedical implants with an improved compressive strength, near bone elastic modulus, controlled porosity, and sufficient surface roughness, can assist in long term implantation. Therefore, the fine process tuning plays its crucial role to develop optimal settings to achieve these desired properties. This paper aims to find applications for fine process tuning in laser powder bed fusion of biomedical Ti alloys for load-bearing implants. Design/methodology/approach In this work, the parametric porosity simulations were initially performed to simulate the process-induced porosity for selective laser-melted Ti 6 Al 4 V as per full factorial design. Continually, the experiments were performed to validate the simulation results and perform multiresponse optimization to fine-tune the processing parameters. Three levels of each control variable, namely, laser power – Pl (180, 190, 200) W, scanning speed – Vs (1500, 1600, 1700) mm/s and scan orientation – Θ{1(0,0), 2(0,67°), 3(0,90°)} were used to investigate the processing performance. The measured properties from this study include compressive yield strength, elastic modulus, process-induced porosity and surface roughness. Finally, confirmatory experiments and comparisons with the already published works were also performed to validate the research results. Findings The results of porosity parametric simulation and experiments in selective laser melting of Ti 6 Al 4 V were found close to each other with overall porosity (less than 10%). The fine process tuning was resulted in optimal settings [Pl (200 W), Vs (1500 mm/s), Θ (0,90°)], [Pl (200 W), Vs (1500 mm/s), Θ (0,67°)], [Pl (200 W), Vs (1500 mm/s), Θ (0,0)] and [Pl (200 W), Vs (1500 mm/s), Θ (0,0)] with higher compressive strength (672.78 MPa), near cortical bone elastic modulus (12.932 GPa), process-induced porosity (0.751%) and minimum surface roughness (2.72 μm). The morphology of the selective laser melted (SLMed) surface indicated that the lack of fusion pores was prominent because of low laser energy density among the laser and powder bed. Confirmatory experimentation revealed that an overall percent improvement of around 15% was found between predicted and the experimental values. Originality/value Since no significant works are available on the collaborative optimization and fine process tuning in laser powder bed fusion of biomedical Ti alloys for different load bearing implants. Therefore, this work involves the comprehensive investigation and multi-objective optimization to determine optimal parametric settings for better mechanical and physical properties. Another novel aspect is the parametric porosity simulation using Ansys Additive to assist in process parameters and their levels selection. As a result, selective laser melted Ti alloys at optimal settings may help in examining the possibility for manufacturing metallic implants for load-bearing applications.

Application of Response Surface Methodology and Machine Learning Approaches to Predict Porosity and Compression Strength of Selective Laser-Sintered Polyamide-12 Scaffold Parts

Revealing the compressive and flow properties of novel bone scaffold structure manufactured by selective laser sintering technique

Potential Assessment in Laser Powder Bed Fusion of Bionic Porous Ti Scaffolds Concerning Compressive Behavior, Porosity, and Surface Roughness

Optimization of Selective Laser Sintering Process Parameters Based on PA12 Powders for Bone Tissue Scaffolds

Investigating the Influence of Additive Manufacturing and Ultrasonic Coating Parameters on Biopolymeric Scaffold Performance Using Response Surface Methodology

Optimization of Structural and Processing Parameters for Selective Laser Melting of Porous 316L Bone Scaffolds

Evaluating Directional Dependency of Selective Laser Sintered Patient Specific Biodegradable Devices to Improve Predictive Modeling and Design Verification

Manufacturability study in laser powder bed fusion of biomedical Ti alloys for orthopedic implants: an investigation of mechanical properties, process-induced porosity and surface roughness

Selective Laser Sintering Process Optimization for Layered Manufacturing of CAPA® 6501 Polycaprolactone Bone Tissue Engineering Scaffolds

Computational Framework to Model the Selective Laser Sintering Process

Micromechanical finite-element modeling and experimental characterization of the compressive mechanical properties of polycaprolactone-hydroxyapatite composite scaffolds prepared by selective laser sintering for bone tissue engineering

Optimization of Selective Laser Sintering Three-Dimensional Printing of Thermoplastic Polyurethane Elastomer: A Statistical Approach

Manufacturability, Mechanical Properties, Mass-Transport Properties and Biocompatibility of Triply Periodic Minimal Surface (TPMS) Porous Scaffolds Fabricated by Selective Laser Melting

Mapping Porous Microstructures to Yield Desired Mechanical Properties for Application in 3D Printed Bone Scaffolds and Orthopaedic Implants

Characterisation and prediction of mechanical properties in laser powder bed fusion-printed parts: a comparative analysis using machine learning

Parameter optimization for accurate and repeatable strut width in the 3D printing of composite bone scaffolds

Optimization of fused deposition modeling parameters to fabricate morphogenesis light weight structure with high tensile and compression strength

Optimization of polydopamine coating process for poly lactic acid‐based 3D printed bone plates using machine learning approaches

An explainable machine learning-based probabilistic framework for the design of scaffolds in bone tissue engineering

Advancing scaffold porosity through a machine learning framework in extrusion based 3D bioprinting

Taguchi-Based Experimental Investigation and Modeling of 3D-Printed PEEK Parts as Biomedical Implants using Fused Deposition Modeling for Improving Mechanical Strength and Surface Quality