Endoscopic retrograde pancreatography (E.R.C.P.) in chronic alcoholism

L. Elsborg,T. Krarup,L. Strandgaard,V. Reinicke

DOI: https://doi.org/10.1007/BF02973523

1980-09-01

Acta Endoscopica

Abstract:

What problem does this paper attempt to address?

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Le Pang,Naomi C. Paxton,Jiongyu Ren,Fan Liu,Haifei Zhan,Maria A. Woodruff,Arixin Bo,Yuantong Gu

DOI: https://doi.org/10.1021/acsami.0c14831

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:Three-dimensional (3D) printing technologies are widely applied in various industries and research fields and are currently the subject of intensive investigation and development. However, high-performance materials that are suitable for 3D printing are still in short supply, which is a major limitation for 3D printing, particularly for biomedical applications. The physicochemical properties of single constituent materials may not be sufficient to meet the needs of modern biotechnology development and production. To enhance the materials' performance and broaden their applications, this work designed and tested a series of titanate nanofiller (nanowire and nanotube)-enhanced polycaprolactone (PCL) composites that were 3D-printable and provided superior mechanical properties. By grafting two different functional groups (phenyl- and thiol-terminated ligands), the nanofiller surface showed improved hydrophobicity, which significantly improved their dispersion in the PCL matrix. After characterizing the surface modification, we evaluated the significance of the homogeneity of the ceramic nanofiller in terms of printability, formability, and mechanical strength. Melt electrowriting additive manufacturing was used to fabricate microfibers of PCL and PCL/nanofiller composites. Improved nanofiller dispersion enabled intact and uniform sample morphology, and in contrast, nanofiller aggregation greatly varied the viscosity during the printing process, which could result in poorly printed structures. Importantly, the modified ceramic/PCL composite delivered enhanced and stable mechanical properties, where its Young's modulus was measured to be 1.67 GPa, which is more than 7 times higher compared to that of pristine PCL (0.22 GPa). Retaining the cell safety properties (comparable to PCL), the concept of enhancing biocompatible polymers with modified nanofillers shows great potential in the field of customized 3D printing for biomedicine.
3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering (SLS) and melt extrusion

Jeong Hun Park,Sarah Jo Tucker,Jeong‐Kee Yoon,YongTae Kim,Scott J. Hollister

DOI: https://doi.org/10.1002/jbm.a.37682

2024-02-14

Journal of Biomedical Materials Research Part A

Abstract:A direct and comprehensive comparative study on different 3D printing modalities was performed. We employed two representative 3D printing modalities, laser‐ and extrusion‐based, which are currently used to produce patient‐specific medical implants for clinical translation, to assess how these two different 3D printing modalities affect printing outcomes. The same solid and porous constructs were created from the same biomaterial, a blend of 96% poly‐ε‐caprolactone (PCL) and 4% hydroxyapatite (HA), using two different 3D printing modalities. Constructs were analyzed to assess their printing characteristics, including morphological, mechanical, and biological properties. We also performed an in vitro accelerated degradation study to compare their degradation behaviors. Despite the same input material, the 3D constructs created from different 3D printing modalities showed distinct differences in morphology, surface roughness and internal void fraction, which resulted in different mechanical properties and cell responses. In addition, the constructs exhibited different degradation rates depending on the 3D printing modalities. Given that each 3D printing modality has inherent characteristics that impact printing outcomes and ultimately implant performance, understanding the characteristics is crucial in selecting the 3D printing modality to create reliable biomedical implants.

engineering, biomedical,materials science, biomaterials
3D printing PLGA: a quantitative examination of the effects of polymer composition and printing parameters on print resolution

Ting Guo,Timothy R Holzberg,Casey G Lim,Feng Gao,Ankit Gargava,Jordan E Trachtenberg,Antonios G Mikos,John P Fisher

DOI: https://doi.org/10.1088/1758-5090/aa6370

2017-04-12

Biofabrication

Abstract:In the past few decades, 3D printing has played a significant role in fabricating scaffolds with consistent, complex structure that meet patient-specific needs in future clinical applications. Although many studies have contributed to this emerging field of additive manufacturing, which includes material development and computer-aided scaffold design, current quantitative analyses do not correlate material properties, printing parameters, and printing outcomes to a great extent. A model that correlates these properties has tremendous potential to standardize 3D printing for tissue engineering and biomaterial science. In this study, we printed poly(lactic-co-glycolic acid) (PLGA) utilizing a direct melt extrusion technique without additional ingredients. We investigated PLGA with various lactic acid:glycolic acid (LA:GA) molecular weight ratios and end caps to demonstrate the dependence of the extrusion process on the polymer composition. Micro-computed tomography was then used to evaluate printed scaffolds containing different LA:GA ratios, composed of different fiber patterns, and processed under different printing conditions. We built a statistical model to reveal the correlation and predominant factors that determine printing precision. Our model showed a strong linear relationship between the actual and predicted precision under different combinations of printing conditions and material compositions. This quantitative examination establishes a significant foreground to 3D print biomaterials following a systematic fabrication procedure. Additionally, our proposed statistical models can be applied to couple specific biomaterials and 3D printing applications for patient implants with particular requirements.

engineering, biomedical,materials science, biomaterials
Maximizing performance and efficiency in 3D printing of polylactic acid biomaterials: Unveiling of microstructural morphology, and implications of process parameters and modeling of the mechanical strength, surface roughness, print time, and print energy for fused filament fabricated (FFF) bioparts

Ray Tahir Mushtaq,Yanen Wang,Chengwei Bao,Mudassar Rehman,Shubham Sharma,Aqib Mashood Khan,Elsayed M-Tag Eldin,Mohamed Abbas

DOI: https://doi.org/10.1016/j.ijbiomac.2024.129201

IF: 8.2

2024-01-15

International Journal of Biological Macromolecules

Abstract:Medical stents, artificial teeth, and grafts are just some of the many applications for additive manufacturing techniques like bio-degradable polylactic acid 3D printing. However, there are drawbacks associated with fused filament fabrication-fabricated objects, including poor surface quality, insufficient mechanical strength, and a lengthy construction time for even a relatively small object. Thus, this study aims to identify the finest polylactic acid 3D printing parameters to maximize print quality while minimizing energy use, print time, flexural and tensile strengths, average surface roughness, and print time, respectively. Specifically, the infill density, printing speed, and layer thickness are all variables that were selected. A full-central-composite design generated 20 samples to test the prediction models' experimental procedures. Validation trial tests were used to show that the experimental findings agreed with the predictions, and analysis of variance was used to verify the importance of the performance characteristics (ANOVA). At layer thickness = 0.26 mm, infill density = 84 %, and print speed = 68.87 mm/s, the following optimized values were measured for PLA: flexural strength = 70.1 MPa, tensile strength = 39.2 MPa, minimum surface roughness = 7.8 μm, print time = 47 min, and print energy = 0.18 kwh. Firms and clinicians may benefit from utilizing the developed, model to better predict the required surface characteristic for various aspects afore trials.

polymer science,biochemistry & molecular biology,chemistry, applied
Device Design and Diagnostic Imaging of Radiopaque 3D Printed Tissue Engineering Scaffolds

Mitchell Delemeester,Kendell M. Pawelec,Jeremy M.L. Hix,James R. Siegenthaler,Micah Lissy,Philippe Douek,Angèle Houmeau,Salim Si-Mohamed,Erik M. Shapiro

DOI: https://doi.org/10.1101/2024.02.26.582070

2024-03-01

Abstract:3D printed biomaterial implants are revolutionizing personalized medicine for tissue repair, especially in orthopedics. In this study, a radiopaque Bi O doped polycaprolactone ( ) composite is developed and implemented to enable the use of diagnostic X-ray technologies, especially photon counting X-ray computed tomography ( ), for comprehensive in vivo device monitoring. PCL filament with homogeneous Bi O nanoparticle ( ) dispersion (0.8 to 11.7 wt%) are first fabricated. Tissue engineered scaffolds ( ) are then 3D printed with the composite filament, optimizing printing parameters for small feature size and severely overhung geometries. These composite TES are characterized via micro-computed tomography ( ), tensile testing, and a cytocompatibility study, with Bi O mass fractions as low as 2 wt% providing excellent radiographic distinguishability, improved tensile properties, and equivalent cytocompatibility of neat PCL. The excellent radiographic distinguishability is validated in situ by imaging 4 and 7 wt% TES in a mouse model with µCT, showing excellent agreement with in vitro measurements. Subsequently, CT image-derived swine menisci are 3D printed with composite filament and re-implanted in their corresponding swine legs . Re-imaging the swine legs via clinical CT allows facile identification of device location and alignment. Finally, the emergent technology of PCCT unambiguously distinguishes implanted menisci in situ.

Bioengineering
Multimodal 3D printing of biodegradable shape memory elastomer resins for patient specific soft tissue repair

Ryan Akman,Harsha Ramaraju,Adam Verga,Scott J. Hollister

DOI: https://doi.org/10.1016/j.apmt.2022.101666

IF: 8.663

2022-11-06

Applied Materials Today

Abstract:Acrylated poly(glycerol-dodecanedioate) (APGD), a biodegradable shape memory polymer, is a photocurable resin developed for 3D printing of biomaterial implants that is especially suited for minimally invasive procedures. 3D printing has numerous advantages over traditional manufacturing modalities including production of complex porous geometries, improved feature resolution, and lower production costs on a per part basis for low volume clinical production. Material extrusion (ME) and vat photopolymerization (VP) printing are two prevalent 3D printing modalities used in tissue engineering. Compared to VP printing, ME printing offers a higher degree of customization by allowing co- or multi-material prints, along with biologic cell printing. VP printing offers higher throughput and capability for printing more complex geometries, versus ME printing, with shorter manufacturing times, making it a more commercially viable choice for clinically translatable materials. Motivated by each printing modalities' unique advantages, APGD resins for ME and VP printing were developed and assessed for crosslinker and photoinitiator (PI) concentration effect on resin time to gel point, storage modulus and viscosity. Increasing crosslinker concentration decreased the gel time and increased the storage modulus of cured resin. Significant differences in printed sample geometry along with material and mechanical properties resulted from using the two printing modalities. ME samples had larger void volume (6.1 ± 1.2% vs. 0.2 ± 0.4%), lower gel content (55.3 ± 2.6% vs. 68.7 ± 1.9%), and less shape fixity (77.4 ± 4.7 vs. 97.3 ± 3.7%) compared to VP samples. VP printing generated complicated 3D anatomic shapes of higher quality than ME printing. In conclusion, this manuscript provides the first report of APGD 3D printing that can be applied to shape memory, resorbable medical devices.

materials science, multidisciplinary
3D printing PCL/nHA bone scaffolds: exploring the influence of material synthesis techniques

Amanda Zimmerling,Zahra Yazdanpanah,David M. L. Cooper,James D. Johnston,Xiongbiao Chen

DOI: https://doi.org/10.1186/s40824-021-00204-y

2021-01-26

Biomaterials Research

Abstract:Abstract Background It is known that a number of parameters can influence the post-printing properties of bone tissue scaffolds. Previous research has primarily focused on the effect of parameters associated with scaffold design (e.g., scaffold porosity) and specific scaffold printing processes (e.g., printing pressure). To our knowledge, no studies have investigated variations in post-printing properties attributed to the techniques used to synthesize the materials for printing (e.g., melt-blending, powder blending, liquid solvent, and solid solvent). Methods Four material preparation techniques were investigated to determine their influence on scaffold properties. Polycaprolactone/nano-hydroxyapatite 30% (wt.) materials were synthesized through melt-blending, powder blending, liquid solvent, and solid solvent techniques. The material printability and the properties of printed scaffolds, in terms of swelling/degradation, mechanical strength, morphology, and thermal properties, were examined and compared to one another using Kruskal-Wallis nonparametric statistical analysis. Results Material prepared through the liquid solvent technique was found to have limited printability, while melt-blended material demonstrated the highest degree of uniformity and lowest extent of swelling and degradation. Scaffolds prepared with powder-blended material demonstrated the highest Young’s modulus, yield strength, and modulus of resilience; however, they also demonstrated the highest degree of variability. The higher degree of inhomogeneity in the material was further supported by thermal gravimetric analysis. While scaffolds printed from melt-blended, powder-blended, and solid solvent materials demonstrated a high degree of micro-porosity, the liquid solvent material preparation technique resulted in minimal micro-porosity. Conclusions Study results indicate that specific techniques used to prepare materials influence the printing process and post-printing scaffold properties. Among the four techniques examined, melt-blended materials were found to be the most favorable, specifically when considering the combination of printability, consistent mechanical properties, and efficient preparation. Techniques determined to be favourable based on the properties investigated should undergo further studies related to biological properties and time-dependent properties beyond 21-days.
Application of Response Surface Methodology and Machine Learning Approaches to Predict Porosity and Compression Strength of Selective Laser-Sintered Polyamide-12 Scaffold Parts

Sai Prasad Kanchi,S. Sundari,Ch. V. S. Parameswara Rao,S. Raju

DOI: https://doi.org/10.1007/s11665-024-09588-z

IF: 2.3

2024-05-30

Journal of Materials Engineering and Performance

Abstract:Recent improvements in Selective Laser Sintering (SLS) technology have prompted researchers to examine the fabrication method as a solution for patient-specific orthopedic issues. Although SLS remains a desirable method for sintering polymer materials, poor selection of process parameter ranges can reduce the porosity of manufactured components and decrease the mechanical performance. This study aims to identify the optimal combination of process parameters to enhance the porosity of the manufactured parts without compromising scaffold strength. Using the SLS technology and response surface methodology-based Box–Behnken design, 17 polymer-based scaffolds were manufactured. Further, the fabricated samples are subjected to compression and porosity tests to determine the effect of pore size, laser power, and scanning speed. To establish an optimum parameter combination, desirability function approach was used. The pore size of 0.6 mm, laser power of 3 W, and scanning speed of 1545 mm/s are found as the optimal parameter combination. Compression strength of 69 MPa and porosity of 35.6% were achieved at the optimal set. The compressive strengths of scaffolds manufactured using the optimal process set are close to the upper limit of the compressive strength of a human fibula bone (67 MPa). Scanning Electron Microscopy (SEM) images were subsequently used to validate the scaffold's porosity at the optimal process factor set. In the development of this work, the study also evaluated the ability of Machine Learning (ML) techniques, namely Gaussian Process Regression (GPR) and Support Vector Machine (SVM), to predict the output responses of scaffold parts. With a coefficient of determination of 0.96, the SVM method exceeds the GBR in terms of its predictive capabilities.

materials science, multidisciplinary
Ultimate metastable solubility of boron in diamond: synthesis of superhard diamondlike BC5.

V. Solozhenko,O. Kurakevych,D. Andrault,Y. Le Godec,M. Mezouar

DOI: https://doi.org/10.1103/PHYSREVLETT.102.015506

IF: 8.6

2009-01-09

Physical Review Letters

Abstract:Here, we report the synthesis of cubic BC5 (c-BC5), the diamondlike B-C phase with the highest boron content ever achieved, at 24 GPa and about 2200 K, using both a laser-heated diamond anvil cell and large-volume multianvil apparatus. The synthesized phase is low compressible (bulk modulus of 335 GPa), conductive, and exhibits extreme Vickers hardness (71 GPa), unusually high for superhard materials fracture toughness (9.5 MPa m;{0.5}), and high thermal stability (up to 1900 K); this makes it an exceptional superabrasive and promising material for high-temperature electronics.
Selective Laser Sintering Process Optimization for Layered Manufacturing of CAPA® 6501 Polycaprolactone Bone Tissue Engineering Scaffolds

Brock Partee,Scott J. Hollister,Suman Das

DOI: https://doi.org/10.1115/1.2162589

2005-09-14

Journal of Manufacturing Science and Engineering

Abstract:Tissue engineering combines principles of the life sciences and engineering to replace and repair damaged human tissue. Present tissue engineering methods generally require the use of porous, bioresorbable scaffolds to serve as temporary three-dimensional templates to guide cell attachment, differentiation, proliferation, and subsequent regenerate tissue formation. Such scaffolds are anticipated to play an important role in allowing physicians to simultaneously reconstruct and regenerate damaged human tissues such as bone, cartilage, ligament, and tendon. Recent research strongly suggests that the choice of scaffold material and its internal porous architecture significantly influence regenerate tissue structure and function. However, a lack of versatile biomaterials processing and manufacturing methods capable of meeting the complex geometric and compositional requirements of tissue engineering scaffolds has slowed progress towards fully testing these promising findings. It is widely accepted that layered manufacturing methods such as selective laser sintering (SLS) have the potential to address these requirements. We have investigated SLS as a technique to fabricate tissue engineering scaffolds composed of polycaprolactone (PCL), one of the most widely investigated biocompatible, bioresorbable materials for tissue engineering applications. In this article, we report on our development of optimal SLS processing parameters for CAPA® 6501 PCL powder using systematic factorial design of experiments. Using the optimal parameters, we manufactured test scaffolds with designed porous channels and achieved dimensional accuracy to within 3%–8% of design specifications and densities approximately 94% relative to full density. Finally, using the optimal SLS process parameters, we demonstrated the successful fabrication of bone tissue engineering scaffolds based on actual minipig and human condyle scaffold designs.
Dietary soy intake is not associated with risk of cardiovascular disease mortality in Singapore Chinese adults.

M. Talaei,W. Koh,R. V. van Dam,Jian-Min Yuan,A. Pan

DOI: https://doi.org/10.3945/jn.114.190454

2014-06-01

Abstract:Although soy food has been recommended because of its presumed cardiovascular benefits, the long-term prospective association between habitual soy food intake and cardiovascular disease mortality remains unclear. This study aimed to evaluate the relation of soy protein and isoflavone intake with the risk of cardiovascular disease mortality in middle-aged and older Chinese adults residing in Singapore. The Singapore Chinese Health Study is a population-based study that recruited 63,257 Chinese adults aged 45-74 y from 1993 to 1998. Usual diet was measured at recruitment by using a validated semiquantitative food-frequency questionnaire, and mortality information was identified via registry linkage until 31 December 2011. Cox proportional hazards models were used to calculate HRs, with adjustment for potential confounders. The median intake was 5.2 g/d for soy protein, 15.8 mg/d for soy isoflavones, and 87.4 g/d for soy expressed as tofu equivalents. We documented 4780 cardiovascular deaths during 890,473 person-years of follow-up. After adjustment for sociodemographic, lifestyle, and other dietary factors, soy protein intake was not significantly associated with cardiovascular disease mortality: HRs (95% CIs) were 1.00 (reference), 1.02 (0.94, 1.11), 1.02 (0.93, 1.11), and 1.06 (0.97, 1.17) for increasing quartiles of soy protein (P-trend = 0.24). Similarly, no significant association was observed for soy isoflavones and total tofu equivalents and when deaths from coronary heart disease (n = 2697) and stroke (n = 1298) were considered separately. When stratified by sex, HRs for cardiovascular disease mortality across quartiles of soy protein were 1.00, 1.00, 1.05, and 1.16 (95% CI: 1.03, 1.31) in men (P-trend = 0.02) and 1.00, 1.01, 0.96, and 0.95 (95% CI: 0.81, 1.10) in women (P-trend = 0.31), although the interaction was not significant (P-interaction = 0.12). In conclusion, soy intake was not significantly associated with risk of cardiovascular disease mortality in the Chinese population. However, a slightly increased risk associated with high soy protein intake in men cannot be excluded and requires further investigation.
Stress management and mutual support groups in rheumatoid arthritis.

M. Shearn,B. Fireman

DOI: https://doi.org/10.1016/0002-9343(85)90282-7

1985-05-01

Abstract:
Mechanical characterization of polylactic acid, polycaprolactone and Lay-Fomm 40 parts manufactured by fused deposition modeling, as a function of the printing parameters

Jessica Zuleima Parrado-Agudelo,Carlos Narváez-Tovar

DOI: https://doi.org/10.15332/iteckne.v16i2.2354

2019-12-16

ITECKNE

Abstract:This study aims to determine the mechanical properties of parts manufactured by Fused Deposition Modeling (FDM) using three biocompatible polymer materials: Polylactic Acid (PLA), Polycaprolactone (PCL) and Lay-Fomm 40. Also, it was analyzed the influence of different printing parameters, material selection, infill percentage, and raster angle, over the mechanical properties. The samples were subjected to tension and compression tests using a universal testing machine, and elastic modulus, yield stress, and ultimate stress were obtained from the stress-strain curves. PLA samples have the highest elastic modulus, yield stress and ultimate stress for both compression and tension tests, for example, the ultimate tensile stress with infill percentage of 30 % and raster angle of 0-90° has an average value of 41.20 MPa, while PCL samples had an ultimate tensile stress average value of 9.68 MPa. On the other hand, Lay-Fomm40 samples had the highest elongations, with percentage values between 300 and 600 %. Finally, ANOVA analysis showed that the choice of the material is the leading printing parameter that contributes to the mechanical properties, with percentages of 84.20% to elastic modulus, 93.30% to yield stress, and 82.44% to ultimate stress. The second important factor is the raster angle, with higher strengths for the 0-90° when compared to 45-135°. On the other hand, the contribution of the infill percentage to the mechanical properties was no statistically significant. The obtained results could be useful for material selection and 3D printing parameters definition for additive manufacturing of scaffolds, implants, and other structures for biomedical and tissue engineering applications.
Device Design and Advanced Computed Tomography of 3D Printed Radiopaque Composite Scaffolds and Meniscus

Mitchell Delemeester,Kendell M. Pawelec,Jeremy M.L. Hix,James R. Siegenthaler,Micah Lissy,Philippe C. Douek,Angèle Houmeau,Salim A. Si‐Mohamed,Erik M. Shapiro

DOI: https://doi.org/10.1002/adfm.202404860

IF: 19

2024-05-19

Advanced Functional Materials

Abstract:A radiopaque bismuth oxide (Bi2O3) doped polycaprolactone composite is created and used to 3D print tissue engineering scaffolds and replacement swine meniscus. These radiopaque implantable biomaterials are easily distinguishable following implantation into animals by using diagnostic X‐ray technologies, especially color K‐edge imaging via spectral photon counting X‐ray computed tomography. 3D‐printed biomaterial implants are revolutionizing personalized medicine for tissue repair, especially in orthopedics. In this study, a radiopaque bismuth oxide (Bi2O3) doped polycaprolactone (PCL) composite is developed and implemented to enable the use of diagnostic X‐ray technologies, especially spectral photon counting X‐ray computed tomography (SPCCT), for comprehensive tissue engineering scaffold (TES) monitoring. PCL filament with homogeneous Bi2O3 nanoparticle (NP) dispersion (0.8 to 11.7 wt%) is first fabricated. TES are then 3D printed with the composite filament, optimizing printing parameters for small features and severely overhung geometries. These composite TES are characterized via micro‐computed tomography (μCT), tensile testing, and a cytocompatibility study, with 2 wt% Bi2O3 NPs providing improved tensile properties, equivalent cytocompatibility to neat PCL, and excellent radiographic distinguishability. Radiographic performance is validated in situ by imaging 4 and 7 wt% Bi2O3 doped PCL TES in a mouse model with μCT, showing excellent agreement with in vitro measurements. Subsequently, CT image‐derived swine menisci are 3D printed with composite filament and re‐implanted in corresponding swine legs ex vivo. Re‐imaging the swine legs via clinical CT allows facile identification of device location and alignment. Finally, the emergent technology of SPCCT unambiguously distinguishes the implanted meniscus in situ via color K‐edge imaging.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Bayesian optimization of 3D bioprinted polycaprolactone/magnesium oxide nanocomposite scaffold using a machine learning technique

Ardeshir Hemasian Etefagh,Mohammad Reza Razfar

DOI: https://doi.org/10.1177/09544054231202219

2023-10-26

Proceedings of the Institution of Mechanical Engineers Part B Journal of Engineering Manufacture

Abstract:Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Ahead of Print. 3D bioprinting of polycaprolactone (PCL) is an additive manufacturing technique, fabricating 3D scaffolds with widespread applications in biomedical bone regeneration. PCL has favorable properties such as tunable mechanical, biological, cytocompatibility, and good printability. In addition, adding magnesium oxide (MgO) nanoparticles effectively enhance bioactivities and bone formation. However, several researchers are reported that PCL-MgO nanocomposite may face challenges in printability. Therefore, this study has focused on optimizing printing parameters to achieve enhanced mechanical and osteoconductivity properties, printability, and print resolution. A newly developed and cost-effective method, Bayesian optimization (BO), has been applied to achieve this objective. The developed model investigates and accelerates the optimization of printing parameters, including air pressure, printing speed, and nozzle temperature on printability and print resolution. Despite the wide search spaces of printing parameters, the BO model drastically reduces the number of experiments to 11 iterations in each target width. There is a good agreement between the model-predicted and actual values (91% in width). Besides, this model can be used to find optimum process parameters in printing gradient width filament to fabricate 3D gradient scaffolds.

engineering, mechanical, manufacturing
The Effect of PCL Addition on 3D-Printable PLA/HA Composite Filaments for the Treatment of Bone Defects

Elin Åkerlund,Anna Diez-Escudero,Ana Grzeszczak,Cecilia Persson

DOI: https://doi.org/10.3390/polym14163305

IF: 5

2022-08-14

Polymers

Abstract:The still-growing field of additive manufacturing (AM), which includes 3D printing, has enabled manufacturing of patient-specific medical devices with high geometrical accuracy in a relatively quick manner. However, the development of materials with specific properties is still ongoing, including those for enhanced bone-repair applications. Such applications seek materials with tailored mechanical properties close to bone tissue and, importantly, that can serve as temporary supports, allowing for new bone ingrowth while the material is resorbed. Thus, controlling the resorption rate of materials for bone applications can support bone healing by balancing new tissue formation and implant resorption. In this regard, this work aimed to study the combination of polylactic acid (PLA), polycaprolactone (PCL) and hydroxyapatite (HA) to develop customized biocompatible and bioresorbable polymer-based composite filaments, through extrusion, for fused filament fabrication (FFF) printing. PLA and PCL were used as supporting polymer matrices while HA was added to enhance the biological activity. The materials were characterized in terms of mechanical properties, thermal stability, chemical composition and morphology. An accelerated degradation study was executed to investigate the impact of degradation on the above-mentioned properties. The results showed that the materials' chemical compositions were not affected by the extrusion nor the printing process. All materials exhibited higher mechanical properties than human trabecular bone, even after degradation with a mass loss of around 30% for the polymer blends and 60% for the composites. It was also apparent that the mineral accelerated the polymer degradation significantly, which can be advantageous for a faster healing time, where support is required only for a shorter time period.

polymer science
Parameter optimization for accurate and repeatable strut width in the 3D printing of composite bone scaffolds

Mahathir Mohammad Bappy,Emma Van Epps,Lauren B. Priddy,Wenmeng Tian

DOI: https://doi.org/10.1016/j.jmapro.2024.09.057

IF: 5.684

2024-10-11

Journal of Manufacturing Processes

Abstract:Critically sized bone defects present a significant challenge to orthopedic surgeons due to the limited availability of autograft bone tissue, which is the current gold-standard treatment. As an alternative, 3D printed porous scaffolds can be designed to mimic bone's mechanical and biochemical properties to support tissue regeneration. However, 3D scaffold printing with high geometric accuracy and repeatability can be challenging, especially when printing new composite materials and geometries. Therefore, the objective of this study was to optimize the extrusion-based 3D bioprinting process parameters for composite polymer-ceramic scaffolds. Bone scaffolds composed of a polylactic- co -glycolic acid (PLGA) and 5 % nano-hydroxyapatite (nHA) composite were printed and analyzed to evaluate their geometric accuracy, which is primarily determined by process parameters. This empirical study investigated the effects of different process parameters, particularly, nozzle temperature, pressure, and printing speed, on the geometric accuracy (i.e., strut width) of the printed scaffolds. Starting with a full factorial design of experiments, in-situ layer-wise optical images were captured, which were analyzed using image processing for strut width characterization. Subsequently, a new iterative process optimization method was proposed that involves regression modeling and bound constraint-based minimization. A case study on printing a two-layer scaffold was used to demonstrate the effectiveness of the proposed method. Overall, the geometric accuracy of the printed scaffolds improved significantly, maintaining a range of ±5 % from the nominal strut width as iterative experiments were conducted, which demonstrates the significant potential of the proposed method in bioprinting process parameter optimization.

engineering, manufacturing
Multiple initiators and dyes for continuous Digital Light Processing (cDLP) additive manufacture of resorbable bone tissue engineering scaffolds

David Dean,Eric Mott,Xinyi Luo,Mallory Busso,Martha O. Wang,Charlotte Vorwald,Ali Siblani,John P. Fisher

DOI: https://doi.org/10.1080/17452759.2013.873337

IF: 10.6

2014-01-02

Virtual and Physical Prototyping

Abstract:The formulation of resorbable polymer resins for light-based additive manufacturing of tissue engineered scaffolds goes beyond resin chemistry. There are at least four parameters that allow the transition from individual layer curing to 3D printing; they are: layer thickness, overcuring, step size, and inter-layer binding. Overcuring is the thickness of the layer minus step size. Overcuring distance limits surface feature resolution in the between-layer direction. Strength is an indication of crosslinking density and a function of inter-layer binding or ‘stitching’. 3D printed scaffolds must be sufficiently strong to endure cleaning of unpolymerised polymer from internal pore spaces without deforming. We report our study of the effect of exposure time on strength and layer thickness while holding step size constant. Increased overcuring dramatically increases scaffold strength. High resolution implants depend on sufficient energy from the light source and a well-tuned resin consisting of: polymer, initiator(s), and perhaps dye(s), solvent(s), and biologic(s).

engineering, manufacturing,materials science, multidisciplinary
Multimodal Three-Dimensional Printing for Micro-Modulation of Scaffold Stiffness Through Machine Learning

Wisarut Kiratitanaporn,Jiaao Guan,David B Berry,Alison Lao,Shaochen Chen

DOI: https://doi.org/10.1089/ten.TEA.2023.0193

Abstract:The ability to precisely control a scaffold's microstructure and geometry with light-based three-dimensional (3D) printing has been widely demonstrated. However, the modulation of scaffold's mechanical properties through prescribed printing parameters is still underexplored. This study demonstrates a novel 3D-printing workflow to create a complex, elastomeric scaffold with precision-engineered stiffness control by utilizing machine learning. Various printing parameters, including the exposure time, light intensity, printing infill, laser pump current, and printing speed were modulated to print poly (glycerol sebacate) acrylate (PGSA) scaffolds with mechanical properties ranging from 49.3 ± 3.3 kPa to 2.8 ± 0.3 MPa. This enables flexibility in spatial stiffness modulation in addition to high-resolution scaffold fabrication. Then, a neural network-based machine learning model was developed and validated to optimize printing parameters to yield scaffolds with user-defined stiffness modulation for two different vat photopolymerization methods: a digital light processing (DLP)-based 3D printer was utilized to rapidly fabricate stiffness-modulated scaffolds with features on the hundreds of micron scale and a two-photon polymerization (2PP) 3D printer was utilized to print fine structures on the submicron scale. A novel 3D-printing workflow was designed to utilize both DLP-based and 2PP 3D printers to create multiscale scaffolds with precision-tuned stiffness control over both gross and fine geometric features. The described workflow can be used to fabricate scaffolds for a variety of tissue engineering applications, specifically for interfacial tissue engineering for which adjacent tissues possess heterogeneous mechanical properties (e.g., muscle-tendon).
Mutational analysis and NMR studies of the death domain of the tumor necrosis factor receptor-1.

J. Telliez,G. Y. Xu,J. Woronicz,S. Hsu,J. Wu,L. Lin,S. Sukits,R. Powers,L. L. Lin

DOI: https://doi.org/10.1006/JMBI.2000.3899

IF: 6.151

2000-07-28

Journal of Molecular Biology

Abstract:Tumor necrosis factor receptor-1 (TNFR-1) death domain (DD) is the intracellular functional domain responsible for the receptor signaling activities. To understand the transduction mechanism of TNFR-1 signaling we performed structural and functional analysis of the TNFR-DD. The secondary structure of the TNFR-DD shows that it consists of six anti-parallel alpha-helices. The determination of the topological fold and an extensive mutagenesis analysis revealed that there are two opposite faces that are involved in self-association and interaction with the TRADD death domain. Interestingly, the same critical residues in TNFR-DD are involved in both interactions. There is a good correlation between the binding activities of the mutant proteins and their cytotoxic activities. These results provide important insight into the molecular interactions mediating TNFR-DD self-association and subsequent recruitment of TRADD in the signaling activity of TNFR-1.

Endoscopic retrograde pancreatography (E.R.C.P.) in chronic alcoholism

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

3D printing modality effect: Distinct printing outcomes dependent on selective laser sintering (SLS) and melt extrusion

3D printing PLGA: a quantitative examination of the effects of polymer composition and printing parameters on print resolution

Maximizing performance and efficiency in 3D printing of polylactic acid biomaterials: Unveiling of microstructural morphology, and implications of process parameters and modeling of the mechanical strength, surface roughness, print time, and print energy for fused filament fabricated (FFF) bioparts

Device Design and Diagnostic Imaging of Radiopaque 3D Printed Tissue Engineering Scaffolds

Multimodal 3D printing of biodegradable shape memory elastomer resins for patient specific soft tissue repair

3D printing PCL/nHA bone scaffolds: exploring the influence of material synthesis techniques

Application of Response Surface Methodology and Machine Learning Approaches to Predict Porosity and Compression Strength of Selective Laser-Sintered Polyamide-12 Scaffold Parts

Ultimate metastable solubility of boron in diamond: synthesis of superhard diamondlike BC5.

Selective Laser Sintering Process Optimization for Layered Manufacturing of CAPA® 6501 Polycaprolactone Bone Tissue Engineering Scaffolds

Dietary soy intake is not associated with risk of cardiovascular disease mortality in Singapore Chinese adults.

Stress management and mutual support groups in rheumatoid arthritis.

Mechanical characterization of polylactic acid, polycaprolactone and Lay-Fomm 40 parts manufactured by fused deposition modeling, as a function of the printing parameters

Device Design and Advanced Computed Tomography of 3D Printed Radiopaque Composite Scaffolds and Meniscus

Bayesian optimization of 3D bioprinted polycaprolactone/magnesium oxide nanocomposite scaffold using a machine learning technique

The Effect of PCL Addition on 3D-Printable PLA/HA Composite Filaments for the Treatment of Bone Defects

Parameter optimization for accurate and repeatable strut width in the 3D printing of composite bone scaffolds

Multiple initiators and dyes for continuous Digital Light Processing (cDLP) additive manufacture of resorbable bone tissue engineering scaffolds

Multimodal Three-Dimensional Printing for Micro-Modulation of Scaffold Stiffness Through Machine Learning

Mutational analysis and NMR studies of the death domain of the tumor necrosis factor receptor-1.